Effect of Zinc Addition on the Mechanical and Corrosion Characteristics of Aluminium Matrix Composites

Year 2021, Volume: 5 Issue: 1, 30 - 37, 03.09.2021

Ademola Agbeleye , Stephen Durowaye , Atinuke Oladoye , Babatunde Bolasodun

Abstract

Aluminium and its alloys are materials of interest because of their availability, unique properties and affordability, which have promoted their application in many areas. This study is aimed at investigating the effect of zinc particulate reinforcement or addition on aluminium matrix. Aluminium cans were reinforced with zinc particulates in varied proportions (0 – 2 wt. %) by mould casting. Morphology (microstructure), mechanical and corrosion characteristics of the composites were examined. The results showed that there was dispersion and dissolution of zinc particulates in the aluminium matrix as indicated by replacement of dark phases with bright ones in the micrographs. The mechanical characteristics indicated a reduction in the hardness of the specimen at 1 wt. % zinc reinforcement. Further increase in zinc concentration improved the hardness of the specimens. The ultimate tensile strength increased with zinc addition but reduced to about 97.2 MPa at 0.75 wt. % zinc addition. The ductility and impact energy of the specimens increased with increasing zinc concentration and likewise the corrosion resistance.

Keywords

Aluminium Cans, Corrosion Resistance, Mechanical Characteristics, Zinc Addition

References

• [1] A.A. Kiffaya, Recycling of Aluminium Beverages Can, Journal of Engineering and Development. 12 (2008) 161-162.
• [2] N. Nafsin, H.M. Rashed, Effects of Copper and Magnesium on Microstructure and Hardness of Al-Cu-Mg Alloys, International Journal of Engineering and Advanced Technology. 2(5) (2013) 533-536.
• [3] J. Wang, Physical Metallurgy of Aluminium Alloys, Aluminium Science and Technology. 2A (2018) 44-79.
• [4] A.J. Khaleed, A.M. Bash, Study of the Effect of Zinc Addition on Dry Sliding Wear Rate of Pure Aluminium, Academic Research International. 4(5) (2013) 234-243.
• [5] B. Khan, M.U. Rosli, H. Jahidi, M.I. Ishak, M. Zakaria, M.R. Jamalludin, Effect of Zinc Addition on the Performance of Aluminium Alloy Sacrificial Anode for Marine Application, American Institute of Physics (AIP) Conference Proceedings, USA, 26 September, 2017, Paper ID: 1885(1) 020074.
• [6] O.M. Oyekeye, S.O. Adeosun, J.S. Ajiboye, A.A. Agbeleye, Strength and Fatigue Life Characteristics of Cold Rolled AA1200 Aluminium Alloy. Paper Presented at Materials Science and Technology, Oregon Convention Centre, Portland, Oregon, USA. 29 September – 3 October, 2019.
• [7] A. Reza, E.E. Robert, H. Reed, Physical Metallurgy Principles, CL Engineering, 4th Edition, 2009.
• [8] S.K. Panigrahi, R. Jayaganthan, Effect of Rolling Temperature on Microstructure and Mechanical Properties of 6063 Al Alloy, Materials Science and Engineering A. 492 (2008) 300–305.
• [9] I.V. Kralia, P.M. Singh, R. Jayaganthan, Experimental Study of Mechanical and Fatigue Behavior of Cryorolled Al 6063 Alloy, International Journal of Mechanical and Materials Engineering. 7(2) (2012) 124-127.
• [10] T.A. Hammer, Deformations, Strain Capacity and Cracking of Concrete in Plastic and Early Hardening Phases, Ph.D. Thesis, Faculty of Engineering Science and Technology, Norwegian University of Science and Technology, Norway, (2007) 1-184.
• [11] J. Friedli, J.L. Fife, P. di-Napoli, M. Rappaz, Dendritic Growth Morphologies in Al-Zn Alloys Part I: X-ray Tomographic Microscopy, Metallurgical and Materials Transactions A. 44(12) (2013) 5522-5531.
• [12] H. Springer, A. Szczepaniak, D. Raabe, On the Role of Zinc on the Formation and Growth of Intermetallic Phases During Interdiffusion Between Steel and Aluminium Alloys, Acta Materialia. 96 (2015) 203–211.
• [13] T. Minoda, H. Yoshida, Effect of Grain Boundary Characteristics on Intergranular Corrosion Resistance of 6061 Aluminium Alloy Extrusion, Metallurgical and Materials Transactions A. 33(9) (2002) 2891-2898.