Effect of Punch Strike Application Strategies on Forming of Fuselage Panel Lay-Up Mold

Year 2024, Volume: 21 Issue: 2, 78 - 89, 01.11.2024

Can Çoğun , Melis Hızarcı İbiş

Abstract

This study examines how three distinct punch strike application techniques affect the cold forming of a 25 mm thick Invar FeNi36 plate into a lay-up mold for an aviation fuselage panel. In each technique, the same number of punch strikes were delivered at various plate positions in varied sequences. The Finite Element Method (FEM) was employed to evaluate the effectiveness of the aforementioned strategies. The most effective approach was the one that produced a form that was most similar to the intended plate form. Additionally, for each stroke of the strategies, the temperature rise, equivalent plastic strain, and maximum stress values of the plate under the punch were compared when the plate was in contact with the mold.

Keywords

Invar FeNi36, Invar FeNi36, Finite Element Analysis, Punch Strike Strategy, Cold Forming

References

• A. Demircan, A. Kayran, and D. F. Kurtuluş, “Kompozit Yapılı Mini İHA'lar İçin Kalıp Üretim Teknikleri ve Aerodinamik Yüzeylerin Üretimi,” IV.UHUK, Hava Harp Okulu, İstanbul, 2012, Eylül 12-14, pp.1-13.
• C. Töre, “Uçakların Yapısal Üretim Teknikleri ve İmalat Takımları (Takım=T00l, Aparat) (Konserve veya Kola Kutusundan Uçak Gövdesi İmalatı Yapılabilir mi?)” Mühendis ve Makine, vol. 43, no. 506, pp. 33-38, 2020.
• Milli Eğitim Bakanlığı, Plastik Teknolojisi-Makina Enjeksiyon Kalıpçılığı-2, MEGEP, Ankara, 2008.
• H. Y. Shahare, A. K. Dubey, P. Kumar, H. Yu, A. Pesin, D. Pustovoytov, and P. Tandon, “A Comparative Investigation of Conventional and Hammering-Assisted Incremental Sheet Forming Processes for AA1050 H14 Sheets,” Metals, vol. 11, no. 11, 1862, pp. 1-17, Nov. 2021, doi:10.3390/met11111862.
• J. K. Paik, J. H. Kim, B. J. Kim, and C. H. Tak, “Analysis of spring-back behavior in the cold-forming process of three-dimensionally curved metal plates,” ASME 29th Int. Conf. on Ocean, Offshore Arctic Eng, pp. 929-934, Jan. 2010, doi:10.1115/OMAE2010-20759.
• X. Li, and S. Hu, “Research Progress of Springback in Multi-Point Forming of Sheet Metal,” J Phys Conf Series, vol. 2101, no. 1, 2101 012006, Nov. 2021, doi:10.1088/1742-6596/2101/1/012006.
• M. Bojahr, H. Prommer, R. Tschullik, and P. Kaeding, “3-Dimensional Forming of Thick Plates–A Comparison of Deep Drawing and an Approach of Rolling and Bending Within a Single Process,” 8th European LSDYNA Conf., Straßburg, France, 2011, May 23-24, pp.1-7.
• A. Köken, and E. Kurt, “Nonlinear Finite Elements Analysis of Different Steel Connections Using Ansys Workbench,” Konya Technical University, 2022.
• QForm, ‘’Software for Simulation and Optimization of Metal Forming Processes and Metal Profile Extrusion.’’ QForm UK. Accessed: Feb. 15, 2024. [Online]. Available: https://www.qform3d.com/products/qform.
• Defense Metal, ‘’Invar 36 (Alloy 36, Nilo 36).’’ Defence Metal. Accessed: Feb. 20, 2020. [Online]. Available: https://www.defencemetal.com/invar-36/.