Starter Selection for Diesel Engines

Year 2023, Volume: 11 Issue: 3, 1296 - 1302, 31.07.2023

Şenol Gülgönül , Nedim Sözbir , Osman Dur

https://doi.org/10.29130/dubited.1210015

Abstract

Starter selection is a critical decision in diesel engine design. The starter performance curves are generally accepted in the industry, with current on the horizontal axis and power, volts, speed and starter torque on the vertical axis. In this way, it is not possible to compare the starter performance curves with the engine friction force curve. In this study, a method has been developed for the selection of suitable starter for diesel engines. With the developed method, the starter performance curve is converted and the engine friction curve is shown on the same graph. With this method, it can be easily understood whether the starter is suitable for a diesel engine. In addition, possible problems that may be encountered during cold start-up can be foreseen. The developed method uses actual performance measurements given by the starter manufacturer. On the engine side, if there is an existing engine, engine friction test results are used. If the engine is in the design phase, the friction force results obtained by simulation are used.

Keywords

Diesel engine, Engine friction, Starter, Cranking

Dizel Motorlarda Marş Motoru Seçimi

Abstract

Marş motoru seçimi, dizel motor tasarımında kritik bir karardır. Marş motoru performans eğrileri endüstride genel kabul gören şekli ile yatay eksende akım, dikey eksende ise güç, volt, hız ve marş motoru torku olacak şekildedir. Bu şekilde marş motoru performans eğrilerinin motor sürtünme kuvveti eğrisi ile karşılaştırılması mümkün olmamaktadır. Bu çalışmada, dizel motorlar için uygun marş motoru seçimine yönelik bir yöntem geliştirilmiştir. Geliştirilen yöntem ile marş motoru performans eğrisi dönüştürülerek, motor sürtünme eğrisi aynı grafik üzerinde gösterilmektedir. Bu yöntem ile marş motorunun dizel motora uygun olup olmadığı kolaylıkla anlaşılabilmektedir. Ayrıca soğuk çalıştırma sırasında karşılaşılabilecek olası problemler öngörülebilmektedir. Geliştirilen yöntem, marş motoru üreticisi tarafından verilen gerçek performans ölçümlerini kullanır. Motor tarafında ise mevcut bir motor varsa motor sürtünme testi sonuçları kullanılır. Eğer motor tasarım aşamasında ise simülasyon ile elde edilen sürtünme kuvveti sonuçları kullanılır.

Keywords

Dizel Motor, Motor Sürtünme Kuvveti, Marş Motoru, Krank

References

• [1] Delprete C, Razavykia A. “Piston ring–liner lubrication and tribological performance evaluation: A review”. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 2018.
• [2] Hopfner, W., Lösch, S., Satschen, S., Winklhofer, E. “Friction test procedures in engine Development”. Proceedings of the Conference: 5. Tribologie und Effizienztagung, Györ, Hungary, 2018.
• [3] Lee, S., Kang, J. & Park, S. “Measurement and modeling of crank train friction in light-duty diesel engines”. J Mech Sci Technol, vol. 34, pp. 889–903, 2020
• [3] Allmaier, H., Knauder, C., Sanders, D. et al. “Combination of Measurement and Simulation to Analyse Engine Friction”. MTZ Worldw, vol. 77, pp. 66–71, 2016
• [4] Johansson, Emma M. V. and Sofia Wagnborg. “Analysis of Engine Cold Start Simulation in GT-Power.” M.S. thesis, Department of Applied Mechanics Division of Combustion, Chalmers University of Technology, Göteborg, Sweden, 2014.
• [5] Iskra Avtoelektrika. (2022, November 25). Starter Motors. [Online]. Available: http://www.iskra-agv.cz/us/pdf/starter_motors.pdf(URL)
• [6] Patil, Atul B., and Nitin S. Ranade. “Computer Simulation of an I.C. Engine During Cranking by a Starter Motor.” SAE Transactions vol. 102: 911–17. 1993
• [7] Vsarath Chandran. (2015, October 16) Starter motor selection and vehicle system considerations. [Online]. Available:https://autoelectricalsystems.wordpress.com/2015/10/19/starter-motor-selection-and-vehicle-system-considerations/
• [8] Azzouaz, George. “Modeling And Simulation Of An Automotive Diesel Engine Cranking System” M.S. thesis, Department of Energy and Environment, Chalmers University of Technology, Göteborg, Sweden, 2005.
• [9]. Mellblom, F. ‘Start modelling for heavy trucks’, Ph.D. dissertation, Department of Electrical Engineering, Linköping University, Linköping, Sweden, 2004.
• [10] Knauder, Christoph & Allmaier, Hannes & Sander, David & Sams, Theodor. “Investigations of the Friction Losses of Different Engine Concepts, Part 1: A Combined Approach for Applying Subassembly-Resolved Friction Loss Analysis on a Modern Passenger-Car Diesel Engine” Lubricants, vol. 7, no. 5, p. 39, Apr. 2019.