Torsional behavior of thin section glass fiber/epoxy composite filament wound tubes: Numerical modelling

Year 2019, Volume: 3 Issue: 2, 52 - 55, 20.06.2019

Mehmet Bulut

https://doi.org/10.26701/ems.526761

Cited By: 1

Abstract

Torsional behavior of thin section glass/epoxy composite pipes was analyzed to study the failure and fracture characteristics based on Hashin’s damage criterion. The variation of shearing stress histories was investigated according to different twisting angles ( θ=20, 40, 60,80,  and 100). For this purpose, composite pipes were modelled by using ABAQUS/explicit subroutine, their stress and force values whether resulting in failure or not as well as failure types in the modelled composites pipes were analyzed within the constant time of the numerical analysis. Results showed that increasing of twist angles by 80 and 100 caused the high amount of shearing failures in the composite pipes while other twist angles did not effected on damage mechanisms over the samples. In addition, increment of the twisting angle after the certain value (θ=60) resulted a slightly increase in force, and followed a force fluctuations after the peak load, implying brittle nature of composite sample.

Keywords

Torsional behavior, glass/epoxy composites, numerical modelling, failure and fracture

References

• Wall, L.D, Jr., Card, M.F. (1971). Torsional shear strength of filament-wound glass-epoxy tubes, NASA Langley Research Center Hampton, Va. 23365, Washington.
• Martins, L.A.L., Bastian, F.L., Netto, T.A. (2014). Reviewing some design issues for filament wound composite tubes. Materials and Design, 55:242-249.
• Kecman, D. (1983). Bending collapse of rectangular and square section tubes. International Journal of Mechanical Sciences, 25:623–636.
• Poonaya, S., Teeboonma, U., Thinvongpituk, C. (2009). Plastic collapse analysis of thin-walled circular tubes subjected to bending. Thin-Walled Structures, 47: 637–645.
• Hilditch, T., Atwell, D., Easton, M., Barnett, M. (2009). Performance of wrought aluminium and magnesium alloy tubes in three-point bending. Materials and Design, 30: 2316- 2322.
• Liu, Y., M.L. Day (2008). Bending collapse of thin-walled circular tubes and computational application. Thin-Walled Structures, 46(4):442–450.
• Rosenow, M.W.K. (1984). Wind angle effects in glass fibre-reinforced polyester filament wound pipes. Composites, 15:144-152.
• Bhavya, S, Kumar, P.R., Kalam, S.A. (2012). Failure Analysis of a Composite Cylinder IOSR Journal of Mechanical and Civil Engineering, 3(1):1-7.
• Kulakov, V.L., Panfilov, N.A., Portnov, G.G. (1996). V. L. Kulakov, N. A. Panfilov, and G. G. Portnov, “Evaluating the feasibility of using composites in ship shafting 1. Analysis of the loads and stress state of a composite shaft. Mechanics of Composite Materials, 31:565-572
• Badie, M.A., Mahdi, E., Hamouda, A.M.S. (2011). An investigation into hybrid carbon/glass fiber reinforced epoxy composite automotive drive shaft. Materials and Design, 32:1485-1500.
• Shokrieh, M.M., Hasani, A., Lessard, L.B. (2004). Shear buckling of a composite drive shaft under torsion. Composite Structures, 64:63-69.
• Gummadi, L.N.B., Palazotto, A.N. (1998). Progressive failure analysis of composite cylindrical shells considering large rotations. Composites Part B, 29:547-563.
• Fujii, T., Lin, F. (1995). Fatigue behavior of a plain-woven glass fabric laminate under tension/torsion biaxial loading. Journal of Composite Materials, 29:573-590.
• Kartik, B., Abishek, V.I., Abishek, R., Kaliyannan, D., Prakash, K.M. (2016). Numerical Simulation of Low Velocity Impact Analysis of Fiber Metal Laminates. Mechanics and Mechanical Engineering, 20:515-530.