Ultrasonik destekli manyetik aşındırıcılarla işleme yönteminde işleme parametrelerinin tel erozyon ile işlenmiş Ti6Al4V alaşımının yüzey kalitesi üzerindeki etkileri

Year 2023, Volume: 38 Issue: 3, 1849 - 1866, 06.01.2023

Mahmut Celik , Hakan Gürün , Ulaş Çaydaş , Uğur Köklü

https://doi.org/10.17341/gazimmfd.1019422

Cited By: 1

Abstract

Mühendislik uygulamalarında kullanılan bileşenlerin üstün mekanik özelliklere sahip olmasının yanı sıra sınırları önceden belirlenmiş geometrik ve boyutsal toleranslar ile yüzey kalitesi kıstaslarını da karşılaması gerekmektedir. Bu beklentilerin karşılanması için geleneksel imalat yöntemleri genelde yetersiz kalmaktadır. Özellikle talaşlı imalatla şekillendirilmesi zor malzemelerin işlenmesinde geleneksel olmayan imalat yöntemlerinin kullanılması zorunlu hale gelmiştir. Bu çalışmada özellikle havacılık uzay ve medikal gibi yüksek teknolojinin kullanıldığı alanlarda sıklıkla kullanılan Ti6Al4V alaşımı, elektro erozyonla işleme (EEİ) yöntemi aracılığıyla işlenmiş ve işlenen yüzeylerin yüzey kaliteleri manyetik aşındırıcılarla işleme (MAİ) yöntemiyle iyileştirilmiştir. Çalışmada, ultrasonik destek, işleme süresi, SiC aşındırıcı boyutu, devir sayısı ve manyetik alan miktarı parametrelerinin, yüzey pürüzlülüğü iyileşme oranı (YPİO) ve talaş kaldırma oranı (TKO) üzerindeki etkileri deneysel olarak araştırılmıştır. Elde edilen deneysel sonuçlar varyans analizi yöntemi ile istatistiksel olarak değerlendirilmiştir. Çalışma sonucunda yüzey kalitelerinin MAİ ve UDMAİ yöntemlerinde ortalama olarak sırasıyla %36 ve %57 oranlarında iyileştirildiği ve bu oranların uygun deney koşullarında sırasıyla %81 ve %90 değerlerine kadar yükseldiği tespit edilmiştir. Öte yandan TKO değerleri MAİ ve UDMAİ yöntemleri için ortalama olarak sırasıyla 4,95 mg/min ve 5,74 mg/min olarak ölçülmüştür. MAİ ve UDMAİ yöntemleri karşılaştırıldığında ise ultrasonik desteğinin YPİO değerleri açısından ortalama % 58, TKO açısından ortalama % 15 oranında olumlu etki yaptığı tespit edilmiştir.

Keywords

Tel erozyonla işleme, Ultrasonik destekli manyetik aşındırıcılarla işleme, Ti6Al4V, Talaş kaldırma oranı, Yüzey kalitesi

Supporting Institution

Gazi Üniversitesi Bilimsel Araştırma Projeleri Birimi

Project Number

07/2020-04

Effect of machining parameters on surface quality of w-edmed Ti6Al4V alloy in ultrasonic assisted magnetic abrasive finishing technique

Abstract

Components used in engineering applications are expected to have superior mechanical properties, as well as geometric properties such as tolerance, accuracy and surface quality. Traditional manufacturing methods are insufficient to meet these expectations. It has become mandatory to use nontraditional manufacturing methods especially in the difficult to cut materials. In this study, Ti6Al4V alloy, which is frequently used in areas where high technology is used such as aviation, space and medical, was machined by electrical discharge machining (EDM) method and the surface qualities of the machined surfaces were improved by magnetic abrasive finishing (MAF) method. In the study, the effects of ultrasonic support, machining time, SiC abrasive size, spindle speed and magnetic field amount parameters on surface roughness improvement rate (SRIR) and material removal rate (MRR) were investigated experimentally. The experimental results obtained were evaluated statistically by variance analysis method. As a result of the study, it was determined that in MAI and UDMAI methods, the surface qualities were improved by 36% and 57%, respectively and these rates increased up to 81% and 90%, respectively, under appropriate test conditions. On the other hand, MRR values were measured as 4.95 mg/min and 5.74 mg/min, respectively, for the MAI and UDMAI methods. When MAI and UDMAI methods were compared, it was determined that ultrasonic assist had a positive effect of 58% on average in terms of SRIR values and 15% on average in terms of MRR.

Keywords

Wire-EDM, Ultrasonic assisted magnetic abrasive finishing, Ti6Al4V, Material removal rate, Surface quality

Project Number

07/2020-04

References

• Çaydaş, U., Çelik, M., and Köklü, U., Investigation of material removal rate and surface roughness in finishing of internal surfaces of AISI 304 L austenitic stainless steel pipes by magnetic abrasives, Journal of the Faculty of Engineering and Architecture of Gazi University, 34 (3), 1213–1225, 2019
• Chen, S. L., Yan, B. H., and Huang, F. Y., Influence of kerosene and distilled water as dielectrics on the electric discharge machining characteristics of Ti-6A1-4V, J. Mater. Process. Technol, 87(1–3), 107–111, 1999.
• He, P., Zhang, J., Zhou, R., and Li, X., Diffusion bonding technology of a titanium alloy to a stainless steel web with an Ni interlayer, Mater. Charact., 43(5), 287–292, 1999.
• Uzun, İ. H., ve Bayındır, F., Dental Uygulamalarda Titanyum ve Özellikleri, Atatürk Üniversitesi Diş Hekimliği Fakültesi Dergisi, 20(2), 213–220, 2010.
• Murr, L. E., Quinones, S. A., Gaytan, S. M., Lopez, M. I., Rodela, A., Martinez, E. Y., and Wicker, R. B., Microstructure and mechanical behavior of Ti-6Al-4V produced by rapid-layer manufacturing, for biomedical applications, J. Mech. Behav. Biomed. Mater., 2(1), 20-32, 2009.
• Ulutan, D., and Ozel, T., Machining induced surface integrity in titanium and nickel alloys: A review, Int. J. Mach. Tools Manuf., 51(3), 250-280, 2011.
• Krishna Alla, R., Ginjupalli, K., Upadhya, N., Shammas, M., Krishna Ravi, R., and Sekhar, R., Surface Roughness of Implants: A Review, Trends Biomater. Artif. Organs, 25(3), 112-118, 2011.
• Bai, T., Liu, J., Zhang, W., and Zou, Z. Effect of surface roughness on the aerodynamic performance of turbine blade cascade, Propulsion and Power Research, 3(2), 82–89, 2014.
• Çelik, Y. H., ve Kiliçkap, E. Titanyum Alaşımlarından Ti-6Al-4V’nın İşlenmesinde Karşılaşılan Zorluklar: Derleme, Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, 6(1), 163–175, 2018.
• Minton, T., Ghani, S., Sammler, F., Bateman, R., Fürstmann, P., and Roeder, M. Temperature of internally-cooled diamond-coated tools for dry-cutting titanium, Int. J. Mach. Tools Manuf., 75, 27–35, 2013.
• Manjaiah, M., Narendranath, S., and Basavarajappa, S., A review on machining of titanium based alloys using EDM and WEDM, Rev. Adv. Mater. Sci., 36(2), 89–111, 2014.
• Çaydaş U., Ti6Al4V Alaşımının Elektro Erozyon Ve Elektro Kimyasal İşleme Yöntemleriyle İşlenebilirliğinin Araştırılması, Doktora Tezi, Fırat Üniversitesi Fen Bilimleri Enstitüsü, Elazığ, 2008.
• Yang, S., and Li, W., Magnetic Abrasive Finishing Technology, Surface finishing theory and new technology. China. National Defense Industry Press, 225-334, 2017.
• Singh, D. K., Jain, V. K., and Raghuram, V., Experimental investigations into forces acting during a magnetic abrasive finishing process, Int. J. Adv. Manuf. Technol., 30(7–8), 652–662, 2006.
• Li, W., Li, X., Yang, S., and Li, W., A newly developed media for magnetic abrasive finishing process: Material removal behavior and finishing performance, J. Mater. Process. Technol., 260, 20–29, 2018.
• Wu, J. Z., & Zou, Y. H., Study on an ultra-precision plane magnetic abrasive finishing process by use of alternating magnetic field, Applied Mechanics and Materials 395–396, 985–989, 2013.
• Kim, T. W., and Kwak, J. S., A study on deburring of magnesium alloy plate by magnetic abrasive polishing, Int. J. Precis. Eng. Manuf., 11(2), 189–194, 2010.
• Vahdati, M., and Rasouli, S. A., Evaluation of Parameters Affecting Magnetic Abrasive Finishing on Concave Freeform Surface of Al Alloy via RSM Method, Adv. Mater. Sci. Eng., 2016, 1-14, 2016.
• Yin, S., and Shinmura, T., Vertical vibration-assisted magnetic abrasive finishing and deburring for magnesium alloy, Int. J. Mach. Tools Manuf., 44(12–13), 1297–1303, 2004.
• Liu, G. Y., Guo, Z. N., Jiang, S. Z., Qu, N. S., and Li, Y. B., A study of processing Al 6061 with electrochemical magnetic abrasive finishing, Procedia CIRP, 14, 234–238, 2014.
• Jiao, A. Y., Quan, H. J., Li, Z. Z., and Zou, Y. H., Study on improving the trajectory to elevate the surface quality of plane magnetic abrasive finishing, Int. J. Adv. Manuf. Technol., 80(9–12), 1613–1623, 2015.
• Kanish, T. C., Narayanan, S., Kuppan, P., and Denis Ashok, S., Investigations on wear behavior of Magnetic Field Assisted Abrasive Finished SS316L material, Mater. Today:. Proc., 5, 12734–12743, 2018.
• Lin, C. T., Yang, L. D., and Chow, H. M., Study of magnetic abrasive finishing in free-form surface operations using the Taguchi method, Int. J. Adv. Manuf. Technol., 34(1–2), 122–130, 2007.
• Kang, J., George, A., and Yamaguchi, H., High-speed internal finishing of capillary tubes by magnetic abrasive finishing, In Procedia CIRP, 1, 414–418, 2012.
• Singh, G., Kumar, H., Kansal, H. K., and Srivastava, A., Effects of chemically assisted magnetic abrasive finishing process parameters on material removal of inconel 625 tubes, Procedia Manuf., 48, 466–473, 2020.
• Singh, G., and Kumar, H., Influence of chemically assisted magnetic abrasive finishing process parameters on external roundness of Inconel 625 tubes. Mater. Today:. Proc., 37 (2021), 3283-3288, 2021.
• Yamaguchi, H., & Shinmura, T., Internal finishing process for alumina ceramic components by a magnetic field assisted finishing process, Precis. Eng., 28(2), 135–142, 2004.
• Kajal, S., Jain, V. K., Ramkumar, J., and Nagdeve, L., Experimental and theoretical investigations into internal magnetic abrasive finishing of a revolver barrel, Int. J. Adv. Manuf. Technol., 100(5–8), 1105–1122, 2019.
• Ihara, I., Nakano, E., McLamore, E., Schueller J. K., Toyoda, K., Umetsu, K., Yamaguchi, H., Cleanability of milk deposits on inner stainless steel tubing surfaces prepared by magnetic abrasive finishing, Eng. Agric. Environ. Food, 10 (1), 63-68, 2017.
• Titanium Alloys - Ti6Al4V Grade 5. AZO Materials. https://www.azom.com/article.aspx?ArticleID=1547, Yayın tarihi Temmuz 2002. Erişim tarihi Mart 11, 2021.
• Misra, A., Pandey, P. M., and Dixit, U. S., Modeling and simulation of surface roughness in ultrasonic assisted magnetic abrasive finishing process. Int. J. Mech. Sci., 133, 344–356, 2017.
• Kanish, T. C., Narayanan, S., Kuppan, P. and Denis, A., S., Experimental Investigations on Magnetic Field Assisted Abrasive Finishing of SS 316L. Procedia Manuf., 30, 276-283, 2019.
• Buj-Corral, I., Álvarez-Flórez, J. and Domínguez-Fernández, A., Effect of grain size and density of abrasive on surface roughness, material removal rate and acoustic emission signal in rough honing processes. Metals, 9(8):860, 2019.
• Misra, A., M. Pandey, P., and Dixit, U. S., Modeling of material removal in ultrasonic assisted magnetic abrasive finishing process. Int. J. Mech. Sci., 131–132, 853–867, 2017.