A New Heat Treatment Cycle Design for High Wear Resistant in PM Steels

Year 2020, Volume: 4 Issue: 3, 193 - 197, 30.09.2020

Onur Altuntaş , Ahmet Güral

https://doi.org/10.30939/ijastech..719815

Abstract

In this study, 1.5% by weight of natural graphite powders were added to Atomet 1001 pure iron powders and unalloyed high carbon powder metallurgy steel specimens were obtained. After the mixture was uniaxial pressed at room temper-ature and 700 Mpa pressing pressure, it was sintered in Ar protected atmosphere controlled oven at 1150 ° C for 20 minutes. The densities of the specimens before and after sintering were measured using precision scales and electronic calipers and presented graphically. After sintering, microstructure specimens containing primary cementite and typical dense perlite colonies were produced. The sintered specimens having primary cementite plus lamellar pearlitic structures were fully quenched from 950 °C temperature and then over-tempered at 705 °C temperature for 60 minutes to produce spherical-fine cementite particles in the ferritic matrix. After by this treatment, these specimens annealed at 735 °C temperature for 3 minutes were austempered at 300 °C salt bath for a period of 1 to 5 hours. After the heat treatment, dry sliding wear tests of specimens were carried out under 10N constant load and 500-1500m wear distance. At the end of the dry sliding wear test, the weight losses of the specimens were measured and it was determined that the dry sliding wear resistance increased with increasing austempering time after spheroidization annealing.

Keywords

Austempering, Spheroidization, Powder metallurgy steel, Microstructure

Supporting Institution

GAZİ ÜNİVERSİTESİ

Project Number

65/2019-05

Thanks

This study has been supported by the Scientific Research Project Program of Gazi University (un-der Project Number 65/2019-05). The authors are grateful to Gazi University for their financial sup-port and the provision of laboratory facilities.

References

• [1] F. Ashrafizadeh, Influence of plasma and gas nitriding on fatigue resistance of plain Carbon (Ck45) steel, Surf. Coat. Technol. 174, 1196–1200, (2003)
• [2] Wu, M. W., Tsao, L. C., Chang, S. Y.: Mater. Sci. Eng. A, 565, 2013, p. 196. doi:10.1016/j.msea.2012.12.032. [3] Pettersson U, Jacobson S. Influence of surface texture on boundary lubricated sliding contacts. Tribol Int 2003;36(11):857–64.
• [4] Xinmin Li, Ulf Olofsson. A study on friction and wear reduction due to porosity in powder metallurgic gear materials. Tribology International 2017; 110, 86–95
• [5] S. Tekeli, A. Güral . Dry sliding wear behaviour of heat treated iron based powder metallurgy steels with 0.3% Graphite + 2% Ni additions. Materials and Design 28 (2007) 1923–1927
• [6] Altuntas, O.. Güral, A. Effect of spheroidizing heat treatment on the microstructure, hardness and toughness of high carbon powder metallurgy steel. Kovove Mater. vol. 55,no. 5, (2017).
• [7] Altuntaş, O.," Investigation of Spherinization Heat Treatment Effects on Microstructre and Impact Toughness Properties on High Carbon Powder Metal Steels", Master Thesis,Gazi University Institute of Science and Technology, (2013).
• [8] Krauss, G. Steels: Processing, Structure, and Performance, ASM International, (2005).
• [9] Smith W.F. (Çev.: Erdoğan, M.) Mühendislik Alaşımlarının Yapı ve Özellikleri, Nobel Yayın, Ankara, (2000).
• [10] Caballero, F.G.,Bhadeshia, H.K.D.H., Mawella, K.J.A., Jones, D.G., Brown, P. Very Strong Low Temperature Bainite, Materials Science and Technology, 18(3):279-284, (2002).
• [11] Sawa M, Rigney DA. Sliding behavior of dual-phase steels in vacuum and air. Wear 1987;119:369–90.