Abstract
References
- D. D. Hanselman, Brushless Permanent Magnet Motor Design, Orono: Electrical and Computer Motorering University of Maine, ISBN 1-881855-15-5, 2003.
- P. M. Dusane, Simulation of a Brushless DC Motor in ANSYS- Maxwell 3D, MSc. Thesis, Czech Technical University in Prague, 2016.
- L. J. Young, G. H. Lee, J. P. Hong and J. Hur, Comparative study of line start permanent magnet, skeleton type brushless and Snail cam type switched reluctance motor for a fan, Sixth International Conference on Electrical Machines and Systems, ICEMS, 1, 183- 186, 2003.
- N. Shrivastava, A. Brahmin, Design of 3-Phase BLDC Motor for Electric Vehicle Application by Using Finite Element Simulation, International Journal of Emerging Technology and Advanced Motorering, 4(1), 2014.
- S. Williamson, T.J Flack, Volschenk A.F. Representation of skew in time-stepped two-dimensional finite-element models of electrical machines, IEEE Transactions on Industry Applications, 31 (5), 1009-1015, 1995.
- IEEE-SA Standards Board. IEEE Recommended Practice and Requirements for Harmonic Control in Electric Power Systems. IEEE Power and Energy Society, IEEE Std 519™-2014.
- T. Waghmare, P.R. Choube, Design Of Internal Permanent Magnet Brushless Dc Motor Using Ansys, International Journal Of Research Publications In Motorering And Technology, ISSN: 2454-7875, 2(4), 2016.
- A. Mujianto, M. Nizam, Comparation of the slot less brushless DC motor (BLDC) and slotted BLDC using 2D modeling, IEEE Int. Conf. On Elec Eng and Comp Sci (ICEECS), DOI:10.1109/ICEECS.2014
- M. Ouada, M.S Meridjet, M S. Saoud and N. Talbi, Increase Efficiency of Photovoltaic Pumping System Based BLDC Motor Using Fuzzy Logic MPPT Control, WSEAS Transactions on Power Systems, 8(3), 2013.
- Y. Li, T. A. Walls, J.D. Loyd, and J. L. Skinner, A noveltwo- phase BPM drive system with high power density and lowcost, IEEE Transaction On Industry Applications, 34(5), 1072- 1080, 1998.
- M. Sameeullah and S. Chandel, Design and Analysis of Solar Electric Rickshaw: A Green Transport Model, IEEE, 2016
- Ansys Electronics Desktop. R1 Rmxprt Help Datasheets, 2022
Abstract
The most basic electrical machine that converts mechanical energy into electrical energy is synchronous machines. Synchronous machines can be operated at high speeds and low speeds for different power plants. In terms of system planning, it is important to examine the operating characteristics of the machine at idle and variable load conditions in these cycles. It is very important that generators, which are the basic components of turbines in power plants, have high efficiency when they are designed. While synchronous generators are being designed, many parameters that are compatible with each other must be arranged in an appropriate way. The efficiency of generators can vary greatly by changing very important parameters in the design. In this study, the analysis, design and analysis of the characteristic parameters of a synchronous generator are carried out with the ANSYS-Maxwell-Rmxprt integrated design and simulation program based on Finite Element Method (FEM). In this paper, parameters such as efficiency, induced voltage, phase currents and voltages and output torque of a three-phase synchronous machine were obtained depending on the electrical angle change.
References
- D. D. Hanselman, Brushless Permanent Magnet Motor Design, Orono: Electrical and Computer Motorering University of Maine, ISBN 1-881855-15-5, 2003.
- P. M. Dusane, Simulation of a Brushless DC Motor in ANSYS- Maxwell 3D, MSc. Thesis, Czech Technical University in Prague, 2016.
- L. J. Young, G. H. Lee, J. P. Hong and J. Hur, Comparative study of line start permanent magnet, skeleton type brushless and Snail cam type switched reluctance motor for a fan, Sixth International Conference on Electrical Machines and Systems, ICEMS, 1, 183- 186, 2003.
- N. Shrivastava, A. Brahmin, Design of 3-Phase BLDC Motor for Electric Vehicle Application by Using Finite Element Simulation, International Journal of Emerging Technology and Advanced Motorering, 4(1), 2014.
- S. Williamson, T.J Flack, Volschenk A.F. Representation of skew in time-stepped two-dimensional finite-element models of electrical machines, IEEE Transactions on Industry Applications, 31 (5), 1009-1015, 1995.
- IEEE-SA Standards Board. IEEE Recommended Practice and Requirements for Harmonic Control in Electric Power Systems. IEEE Power and Energy Society, IEEE Std 519™-2014.
- T. Waghmare, P.R. Choube, Design Of Internal Permanent Magnet Brushless Dc Motor Using Ansys, International Journal Of Research Publications In Motorering And Technology, ISSN: 2454-7875, 2(4), 2016.
- A. Mujianto, M. Nizam, Comparation of the slot less brushless DC motor (BLDC) and slotted BLDC using 2D modeling, IEEE Int. Conf. On Elec Eng and Comp Sci (ICEECS), DOI:10.1109/ICEECS.2014
- M. Ouada, M.S Meridjet, M S. Saoud and N. Talbi, Increase Efficiency of Photovoltaic Pumping System Based BLDC Motor Using Fuzzy Logic MPPT Control, WSEAS Transactions on Power Systems, 8(3), 2013.
- Y. Li, T. A. Walls, J.D. Loyd, and J. L. Skinner, A noveltwo- phase BPM drive system with high power density and lowcost, IEEE Transaction On Industry Applications, 34(5), 1072- 1080, 1998.
- M. Sameeullah and S. Chandel, Design and Analysis of Solar Electric Rickshaw: A Green Transport Model, IEEE, 2016
- Ansys Electronics Desktop. R1 Rmxprt Help Datasheets, 2022
Details
| Primary Language | English |
|---|---|
| Subjects | Engineering |
| Journal Section | Articles |
| Authors | |
| Publication Date | December 20, 2022 |
| Acceptance Date | October 11, 2022 |
| Published in Issue | Year 2022 |