Kompozit Levhaların Tamirinde Yama Özelliklerinin Çekme Gerilme Davranışlarına Etkisi

Year 2023, Volume: 4 Issue: 1, 1 - 8, 21.06.2023

Abdullah Şişman , Mehmet Ramazanoğlu

https://doi.org/10.53525/jster.1200014

Abstract

Bu çalışmada, eliptik hasarlı tabakalı kompozit levhaların tamirinde yama boyutlarının ve yama tabaka sayısının çekme gerilme davranışına etkisi deneysel olarak araştırılmıştır. Bu amaçla, eliptik delikli cam elyaf takviyeli lamine kompozit levhalar hazırlanmıştır. Bu plakalar çekme yüklerine maruz bırakılmış ve kırılma yükleri deneysel olarak belirlenmiştir. Daha sonra DP460 yapıştırıcı malzeme kullanılarak, eliptik hasarlı cam elyaf takviyeli kompozit levhalar, tek taraflı bindirmeli bağlantıları kullanılarak, değişen boyut ve katman sayılarına sahip cam elyaf takviyeli kompozit yamalarla onarılmış ve onarılan numuneler çekme yüklerine maruz bırakılmış ve kırılma yükleri belirlenmiş ve gerilme davranışı üzerindeki etkileri deneysel olarak araştırılmıştır.

Keywords

Cam fiber takviyeli kompozitler, Tek taraflı bindirme bağlantıları, çekme gerilme davranışları

The Effect of Patching Properties on Tensile Stress Behaviours in The Repair of Composite Plates

Abstract

In this study, the effect of patch sizes and number of patch layers on tensile stress behavior in the repair of elliptical damaged laminated composite sheets was investigated experimentally. For this purpose, glass fiber reinforced laminated composite sheets with elliptical holes were prepared. These plates were subjected to tensile loads and their failure loads were determined experimentally. Then, using DP460 adhesive material, glass fiber reinforced composite sheets with elliptical damage were repaired using single-sided lap joints with glass fiber reinforced composite patches of varying sizes and layer numbers, and the repaired samples were subjected to tensile loads and their failure loads were determined and its effects on stress behavior were also investigated experimentally.

Keywords

Glass Fiber Reinforced Composite, Single-Sided Lap Joints, Tensile Stress Properties

References

• Ergün, Raşit Koray “”Experimental and Numerical Investigation of the Effect of Repairing Elliptical Perforated Aluminum Sheets with Composite Patch on Tensile Behavior”, (Kahramanmaraş Sütçü İmam University Institute of Science and Technology, Unpublished Master Thesis), Kahramanmaraş 2014.
• Gülakman, Ahmet “Glass/Epoxy Material Production, Determination of Mechanical Properties and Calculation of Interface Fracture Toughness”, (Dokuz Eylül University Institute of Science, Published Master Thesis), İzmir 2008. Li HCH, Wangb J., Baker A., “ Rapid Composite Bonded Repair for Helicopter Tail Drive Shafts”, Composites: Part B , 43 : (2012), pp. 1579-1585
• Rachid M., Serier B., Bachir BB, Belhouari M., “Numerical Analysis of the Patch Shape Effects on the Performances of Bonded Composite Repair in Aircraft Structures”, Composites: Part B , 43 : (2012), pp. 391-397.
• Ramji M., Srilakshmi R., Bhanu PM, “Towards Optimization of Patch Shape on the Performance of Bonded Composite Repair Using FEM”. Composites: Part B , 45: (2013), pp. 710-720.
• Free, Ali Kamil “Rubber Material Pair Using Post-Adhesive Method”, (Uludağ University Institute of Science and Technology, Published Master's Thesis), Bursa 2013.
• Soy, Ugur “Adhesive Repair of Al 2024-T3 Alloy Plate with Composite Patch with the Help of Computer Aided Modeling”, (Sakarya University Institute of Science and Technology, Published Master's Thesis), Sakarya 2005.
• Single, Gökhan “Single and Double-Action Adhesive Connections”, (Gazi University Institute of Science, Published Master Thesis), Ankara 2011 .