Investigate the Fluctuation Size in Thrust Force and Chip Morphology in Drilling

Yıl 2018, Cilt: 14 Sayı: 4, 385 - 397, 28.12.2018

Zülküf Demir

https://doi.org/10.18466/cbayarfbe.409399

Cited By: 1

Öz

Drilling is a widely used production method, having a broad range of applications
taking part in machining operations. The length of the cutting edge of the
drill causes variations in cutting speed, resulting in undesired outputs. In
order to decrease this adverse impact in drilling, selecting higher point
angles is an obligation, associated with three different kinds of feed rates
and spindle speeds. The aim of this study is to investigate the effect of feed
rate, spindle speed, and point angle on the fluctuation size in thrust force
besides the effect of the fluctuation size in thrust force on the surface
roughness, tool wear and chip morphology. In conclusion, while higher point
angles provided optimum outputs such as lower fluctuation size in thrust force,
less tool wear, better surface quality and continuous chip form, the effect of
feed rate and spindle speed on these outputs varied depending on each other.
With the stability in fluctuation size in thrust force, less tool wear took
place, and better surface quality and continuous chip form were achieved. However,
due to the effect of vibrations, higher fluctuation size in thrust force caused
undesired outputs, such as poor surface quality, more tool wear, removal chip
in short and brittle form during the drilling operations.

Anahtar Kelimeler

Drilling, Thrust force, Tool wear, Chip morphology, Machinability, Surface quality, Thrust force fluctuation, Drill point angle

Kaynakça

• 1. Thakre, A.A, Soni, S, Modelling of burr size in drilling of aluminium silicon carbide composites using response surface methodology, Engineering Science and Technology an International Journal, 2016, 19, 1199-1205.
• 2. Chen, W.C, Tsao, C.C, Cutting performance of different coated twist drills, Journal of Materials Processing Technology, 1999, 88, 203 – 207.
• 3. Lazar, M. B, Xiraouchhakis, P, Mechanical load distribution along the main cutting edges in drilling, Journal of Materials Processing Technology, 2013, 213, 245 – 260.
• 4. Kalidas, S. R, Devor, E, Kapoor, S. G, Experimental investigation of the effect of drilling coatings on hole quality under dry and wet drilling conditions, Surface and Coatings Technology, 2001, 148, 117 – 128.
• 5. Puneeth, H. V, Smitha, B.S, Studies on tool life and cutting forces for drilling operation using uncoated and coated HSS tool, International Research Journal of Engineering and Technology, 2017, 4, 1949-1954.
• 6. Ema, S, Effect of twist drill point geometry on torque and thrust, Science Report of Faculty of Education Gifu University (Natural Science), 2012, 36, 165-174.
• 7. Çaydas, U, Çelik, M, Investigation of the effects of cutting parameters on the surface roughness, tool temperature and thrust force in drilling of AA 7075-T651 alloy, Journal of Polytechnic, 2017, 20(2), 419–425. 8. Parsian, A, Magnevall, M, Eynian, M, Beno, T, Time domain simulation of chatter vibration in indexable drills, International Journal of Advanced Manufacturing Technology, 2017, 89, 1209-1221.
• 9. Wosniak, F. A, Polli, M. L, Beltrao, P. A. C, Study on tool wear and chip shapes in deep drilling of AISI 4150 steel, Journal of the Brazilian Society of Mechanical Sciences and Technology, 2016, 89, 3535-3545.
• 10. Saoudi, J, Zitoune, R, Mezlini, S, Gururaja, S, Seitier, P, Critical thrust force predictions during drilling: Analytical modeling and X-ray tomography quantification, Composite Structures, 2016, 153, 886–894.
• 11. Tsao, C. C, Hocheng, H, The effect of chisel length and associated pilot hole on delamination when drilling composite materials, International Journal of Machine Tools & Manufacture, 2003, 43, 1087-1092.
• 12. Feng, P, Wang, J, Zhang, J, Zheng, J, Drilling induced tearing defects in rotary ultrasonic machining of C/SiC, Ceramics International, 2017, 43, 791-799.
• 13. Sreenivasulu, R, Rao, C.S, Effect of drilling parameters on thrust force and torque during drilling of aluminium 6061 alloy-based on taguchi design of experiments, Journal of Mechanical Engineering, 2016, 46, 41-48.
• 14. Samy, G. S, Kumaran, S. T, Measurement and analysis of temperature, thrust force and surface roughness in drilling of AA (6351)-B4C composite, Measurement, 2017, 103, 1–9.
• 15. Çelik, Y. H, Yildiz, H, Özek, C, Effect of cutting parameters on workpiece and tool properties during drilling of Ti-Al-4V, Wear Testing, 2006, 46, 1526–1535.
• 16. Çelik, Y. H, Investigation the effect of cutting parameters on the hole quality in drilling the Ti-6Al-4V, Materials and Technology, 2014, 95, 669-295.
• 17. Çaydas, U, Hasçalık, A, Buytoz, Ö, Meyveci, B, Performance evaluation of different twist drills in dry drilling of AISI 304 austenitic stainless steel, Materials and Manufacturing Processes, 2011, 26, 951-960.
• 18. Sultan, A. Z, Sharif, S, Kurniawan, D, Chip formation when drilling AISI 316L stainless steel using carbide twist drill, Procedia Manufacturing, 2015, 2, 224-229.
• 19. Astakhov, V. P, Drills, science and technology of advanced operations, 1st English edn. Taylor Francis Group LLC Press, Boca Raton, London, New York, 2014, pp 214.
• 20. Trent EM. Metal cutting, metal cutting operations and terminology, Uni. Birmingham Press, 2nd edn, Birmingham, UK, 1984, pp 8.