A Parameter Monitoring System for Induction Motors Based on Zigbee Protocol

Yıl 2011, Cilt: 24 Sayı: 4, 763 - 771, 16.12.2011

Ramazan Bayındır , Mehmet Sen

Öz

In this study, a wireless control and monitoring system for an induction motor is realized using the Zigbee communication protocol for safe and economic data communication in industrial fields where the wired communication is either more expensive or impossible due to physical conditions. The induction motor can be started and stopped wireless due to the computer interface developed with Zigbee. It is also possible to protect of the motor against some faults such as over current, higher/lower voltage, over temperature in windings, overloading of motor. Moreover, a database is built to execute online measurements and to save the motor parameters received by radio frequency (RF) data acquisition system. Therefore, controlling, monitoring, and protection of the system are realized in real time. Since the wireless communication technology is used in this study, controlling abilities of the system are increased and also hardware and the necessities of other similar equipment for data communication are minimized.

 

Key Words: Induction motor, Zigbee, wireless data communication

Anahtar Kelimeler

Induction motor, Zigbee, wireless data communication

Based on Zigbee Protocol

Öz

Kaynakça

• Hazzab A., Bousserhane IK., Zerbo M. and Sicard P. “Real Time Implementation of Fuzzy Gain Scheduling of PI Controller for Induction Motor Machine Control”, Neural Processing
• Letters, .24 (3): 203-215, (2006).
• Zhang P., Du Y., Habetler TG, Lu B., “A Survey of Condition Monitoring and Protection Methods for Medium-Voltage Induction Motors”, IEEE Transactions On Industry Applications,.47 (1): 34-45 (2011).
• Vas, P., “Sensorless Vector and Direct Torque Control”, Oxford University Press, New York, 31-60 (1998).
• Vas, P., “Parameter Estimation, Condition Monitoring, and Diagnosis of Electrical Machines”, Clarendon Press, Oxford, (1993).
• Yanfei L., Cheng W., Chengbo Y., Xiaojun Q., “Research on Zigbee wireless sensors network based on modbus protocol”, International Forum on Information Technology and Applications, 2009. IFITA '09, Chengdu, China, 1: 487 – 490, (2009).
• Li J., Zhu X., Tang N., Sui J., “Study on ZigBee network architecture and routing algorithm”, 2nd International Conference on Signal Processing Systems (ICSPS), Dalian China, 2 389 - 393 (2010).
• Masica, K., “Recommended practices guide door securing Xbee wireless networks in process control system environments”, Lawrence Livermore National Laboratory, 9-19 (2007).
• Bayındır R., Sefa İ., Çolak İ., Bektaş A., “Fault detection and protection of induction motors using sensors”, IEEE Transactions on Energy Conversion, 23(3): 734-741 (2008).
• Bayındır, R., Demirbaş, Ş., Irmak, E., Bekiroğlu, E., “Design and implementation of microcontroller based starting and protection relay for induction motors”, Journal of Polytechnic, 1: 1-2(2007).
• Siddique, A., Yadava, G. S., Singh, B. A., “Review of stator fault monitoring techniques of induction motors.” IEEE Transactions on Energy Conversion, 20 (1): 106-114 (2005).
• Tandon, N., Yadava, G. S., Ramakrishna, K. M. A., “Comparison of some condition monitoring techniques for the detection of defect in induction motor ball bearings”, Mechanical Systems and Signal Processing, 21 (1): 244-256 (2007).
• Bayindir R., Sefa İ., “Novel approach based on microcontroller to online protection of induction motors”, Energy Conversion and Management, 48 (3): 850-856, (March 2007).
• Çolak İ., Çelik H., Sefa İ. And Demirbaş Ş., “On line protection system for induction motors”, Energy Conversion and Management, 46: 2773- 2786 (2005).
• Bektaş, A., Çolak, İ., Bayındır, R., “A PLC based application for induction motor protection”, Journal of Polytechnic, 10 (2): 117 (2007).
• IEEE STD 802.15.4.www.zigbee.org.
• Cao L., Jiang W., Zhang Z., “Networked wireless meter reading system based on ZigBee technology”, Control and Decision Conference, Chinese, 3455 – 3460 (2008).
• Park WK., Choi CS., Han J., Han I., “Design and implementation of ZigBee based URC applicable to legacy home appliances”, IEEE International Symposium Consumer Electronics, 2007.1-6 (2007). ISCE
• Yiming Z., Xianglong Y., Xishan G., Mingang Z., Liren W., “A design of greenhouse monitoring & control system based on zigbee wireless sensor network”, International Conference Wireless Communications, Networking and Mobile Computing, WiCom 2007, 2563 – 2567 (2007).
• Watanabe K., Ise M., Niwamoto H., “An energy- efficient architecture of wireless home network based on MAC broadcast and transmission power control”, IEEE Transactions on Consumer Electronics,.53 (1): 124-130 (2007).
• Park WK., Han I., Park KR., “ZigBee based dynamic scheme for multiple legacy IR controllable digital consumer devices”. IEEE Transactions on Consumer Electronics,.53 (1): 172-177 (2007).
• Dong Y., Gu P., Si S., “The implementation of indoor location system to control ZigBee home network”. SICE-ICASE 2006 in Bexco, Busan, Korea,.10: 2158-2161 (2006).
• Choi JM., Ahn BK., You-Sung Cha YS., “Remote-controlled home robot server with ZigBee sensor network”, SICE-ICASE 2006 in Bexco, Busan, Korea, 10: 3739-3743 (2006).
• Gang Z., Shuguang L, “Study on electrical switching device junction temperature monitoring system based on Zigbee technology”, International Conference on Computer Application and System Modeling (ICCASM), Taiyuan, China,.4: 692-695 (2010).
• Zhu XQ., Wang JM., “The research and implementation of ZigBee protocol network” Journal of Electronic Technology, 1:129-132 (2006).
• Li J., Zhu X., Tang N., Sui J., “Study on ZigBee network architecture and routing algorithm”, 2nd International Conference on Signal Processing Systems (ICSPS), Dalian China, 2: 389 - 393 (2010).
• Baran L., “A PLC based monitoring and control of power factor of a three phase induction motors”, MSc Thesis, Gazi University, Institute of Science and Technology, Ankara (2009).