Güçlendirilmiş Polyester Reçine Matrisli Kompozit Malzemelerin Tek Yönlü Karbon Fiberler Üzerinde Katmanların Etkisi

Yıl 2022, Cilt: 10 Sayı: 3, 495 - 503, 30.09.2022

Levent Urtekin , Deniz Gunes , Faik Yılan , Murat Çanlı

https://doi.org/10.29109/gujsc.1105848

Cited By: 2

Öz

Bu çalışmada, 12 filament numaralı tek yönlü karbon fiber takviyelerin polyester matris içerisine bir, iki ve üç katman oluşturacak şekilde oda sıcaklığında elle yatırma yöntemiyle yerleştirilmesiyle kompozit malzemeler üretilmiştir. Numuneler, standartlara uygun olarak elyaf yön açısı doğrultusunda bir kalıp yardımıyla kompozit plakalardan hazırlanır. Numunelerin mekanik özelliklerinin belirlenmesi için çekme, eğilme ve düşme ağırlıklı düşük hızlı darbe testleri yapılır. Çekme testi sonucunda katmanlar arasında en yüksek çekme dayanımı değeri iki katmanlı tek yönlü elyaf takviyeli kompozit malzemelerde elde edilmiştir. Eğilme testlerinde tek yönlü karbon elyaf takviyelerin en yüksek elastisite değerleri 00 dogrultusunda üç katmanlı kompozit malzemelerde gözlenmektedir. 00 tek yönlü güçlendirilmiş kompozit malzemelerin düşen ağırlıkta düşük hız darbe testlerinin en yüksek deformasyon değerlerine sahip kompozit malzemelerde görülmektedir.

Anahtar Kelimeler

Carbon Fiber, Composite, Mechanical Properties, Polyester Resin

The Effect of Layers on the Unidirectional Carbon Fibers of the Reinforced Polyester Resin Matrix Composite Material

Öz

In this study, composite materials are produced, placing unidirectional carbon fiber reinforcements with 12 filament numbers in a polyester matrix to form one, two, and three layers at room temperature through the hand lay-up method. The samples are prepared from composite plates with the help of a mold in line with the fiber direction angle by the standards. The tensile, three-point bending, and falling weight low-speed impact strength values of the samples were measured and were investigated the mechanical performance of the specimens. As a result of the tensile test, the highest tensile strength value among layers is obtained in the two-layer unidirectional fiber-reinforced composite materials. In bending tests, the highest elasticity values of unidirectional carbon fiber reinforcements are observed in three-layer composite materials with a fiber direction angle of 00. 00 unidirectional fiber-reinforced one-layer composite materials are observed in composite materials with the highest deformation values in the falling weight low-velocity impact tests.

Anahtar Kelimeler

Carbon Fiber, Composite Materials, Mechanical Performance, Polyester Resin

Kaynakça

• [1] Clyne, Trevor William, and Derek Hull. An introduction to composite materials. Cambridge university press, 2019.
• [2] Jones, Robert M. Mechanics of composite materials. CRC press, 2018.
• [3] Kollar, Laszlo P., and George S. Springer. Mechanics of composite structures. Cambridge university press, 2003.
• [4] Mallick, P. K. "Fiber Reinforced Composites, Materials, Manufacturing, and Design, Marcel Decker." Inc., New York (1993).
• [5] Zhang, Xiaoqing, et al. "Interfacial microstructure and properties of carbon fiber composites modified with graphene oxide." ACS applied materials & interfaces 4.3 (2012): 1543-1552.
• [6] Karnati, Sidharth Reddy, Philip Agbo, and Lifeng Zhang. "Applications of silica nanoparticles in glass/carbon fiber-reinforced epoxy nanocomposite." Composites Communications 17 (2020): 32-41.
• [7] Botelho, E. C., M. C. Rezende, and B. Lauke. "Mechanical behavior of carbon fiber reinforced polyamide composites." Composites Science and Technology 63.13 (2003): 1843-1855.
• [8] Cao, Shenghu, W. U. Zhis, and Xin Wang. "Tensile properties of CFRP and hybrid FRP composites at elevated temperatures." Journal of composite materials 43.4 (2009): 315-330.
• [9] Murugan, Ramasamy, R. Ramesh, and Krishan Padmanabhan. "Investigation on static and dynamic mechanical properties of epoxy based woven fabric glass/carbon hybrid composite laminates." Procedia Engineering 97 (2014): 459-468.
• [10] Sugie, Tomohiko, Asami Nakai, and Hiroyuki Hamada. "Effect of CF/GF fibre hybrid on impact properties of multi-axial warp knitted fabric composite materials." Composites Part A: Applied Science and Manufacturing 40.12 (2009): 1982-1990.
• [11] Boumbimba, R. Matadi, et al. "Preparation and mechanical characterisation of laminate composites made of glass fibre/epoxy resin filled with tri bloc copolymers." Composite structures 116 (2014): 414-422.
• [12] Güneş, D., Çanlı, M, and Urtekin, L. "Investigation of Mechanical Properties of Carbon Fibre Reinforced Polyester Matrix Composite." Journal of Scientific Reports-A 047: 68-78.
• [13] Fiore, V. I. N. C. E. N. Z. O., G. Di Bella, and A. Valenza. "Glass–basalt/epoxy hybrid composites for marine applications." Materials & Design 32.4 (2011): 2091-2099.
• [14] Banakar, Prashanth, and H. K. Shivananda. "Preparation and characterization of the carbon fiber reinforced epoxy resin composites." Department of Mechanical Engineering, Atria Institute of Technology, Visvesvaraya University, Bangalore-24, India. Department Of Mechanical Engineering, University Visvesvaraya College of Engineering, Bangalore University Bangalore-01, India ISSN (2012): 2278-1684.