Investigation of Groove Width Created by Fiber Laser on ST52 Steel

Yıl 2024, , 45 - 60, 30.06.2024

Satılmış Ürgün , Mustafa Özgür Bora , Sinan Fidan , Timur Canel

https://doi.org/10.38061/idunas.1496031

Öz

This paper has presented the results of a study aiming to identify the effects of laser power and two other parameters on groove formation in ST52 steel using a fiber laser and to optimize these parameters so that the groove aspect ratio could be maximized. The Taguchi method has been used to explore the effects of three parameters, namely, laser power, scan speed, and frequency, on the laser grooving characteristics. The analysis has shown that the first parameter has a strong impact of about 69.95 %, while the other two have led to about 15.73 % and 14.31 %, respectively. Each scenario included three arrangements of factors and levels that corresponded to the L9 orthogonal array. Subsequently, a total of nine experiments were conducted, with an extensive variation in the formed grooves observed. The obtained results have shown that the groove’s deepness and grooves’ width vary substantially when the laser step settings through the developed quantitative range. The subsequent achievement in optimal response elaboration has the following ratio: 100 W laser power, 100 mm/s scan speed, and 20 kHz is a frequency. Moreover, the described ration corresponds to values derived through regression analysis. For that reason, the performed research provides a valuable contribution to furthering knowledge in laser-material interaction during the texturing procedure.

Anahtar Kelimeler

Surface texturing, Fiber Laser machining, ST52 Steel, Taguchi Optimization, Surface Groove.

Destekleyen Kurum

Kocaeli Üniversitesi, Bilimsel-Araştırma-Projeleri Koordinasyon-Birimi

Proje Numarası

FBA-2024-3704

Kaynakça

• 1. Alloni C, D'Agostino A, Priarone R. (1976). Design Analysis and Construction of the Loango Steel Gravity Platforms. Offshore Technology Conference. Paper Number Otc 2437
• 2. Boydak Ö., Keskinkılıç S., Koçak M., Microstructural and Mechanical Characterization of High Temperature and Creep Resistant Steel Weldments. 63rd Annual Assembly & International Conference of the International Institute of Welding. AWST-10/130
• 3. Brown, G., & Patel, H. (2024). Metaheuristic Algorithms in Predicting Erosion Behavior of Polymers. Polymer Testing. https://doi.org/10.1016/j.polymertesting.2024.107458
• 4. Cunha, Â.; Bartolomeu, F.; Silva, F.; Trindade, B.; Carvalho, Ó. (2022) Influence of Laser Parameters on the Texturing of 420 Stainless Steel. Materials, 15, 8979
• 5. Gloc M., Wachowski M., Plocinski T., Kurzydlowski K.J., Microstructural and microanalysis investigations of bond titanium grade1/low alloy steel st52-3N obtained by explosive welding. J. Alloys Compd. 671. 446e451
• 6. Haghshenas M., Gerlich A.P., Joining of automotive sheet materials by friction-based welding methods: A review. Eng. Sci. and Tech., an Int. J. 21. 130–148
• 7. Hashmi A. W. Mali H.S., Meena A., Improving the surface characteristics of additively manufactured parts: A review, Mater. Today: Proc. 81. 723–738
• 8. Iroha N.B., Nnanna L. A., Maduelosi N.J., Anadebe V.C., Abeng F.E., (2022). Evaluation of the anticorrosion performance ofTamsulosin as corrosion inhibitor for pipelinesteel in acidic environment: experimental andtheoretical study. J Taibah Univ Sci. Vol. 16, No. 1, 288–299.
• 9. Langseth M. Lindholm U. S., Larsen P. K., Lian B., (1991). Strain-Rate Sensitivity of Mild Steel Grade ST52-3N, J. Eng. Mech., 117(4): 719-732
• 10. Liu, C., & Wang, D. (2023). Optimization of Process Parameters for Laser Machining Using Response Surface Methodology. Journal of Materials Processing Technology. https://doi.org/10.1016/j.jmatprotec.2023.117123
• 11. Lyubomir L., Edmunds T., Nikolay . and Emil Y., (2023) Laser Phys. 33 046001 (7pp)
• 12. Moldovan, E.R.; Concheso Doria, C.; Ocaña, J.L.; Baltes, L.S.; Stanciu, E.M.; Croitoru, C.; Pascu, A.; Roata, I.C.; Tierean, M.H. (2022) Wettability and Surface Roughness Analysis of Laser Surface Texturing of AISI 430 Stainless Steel. Materials, 15, 2955. https://doi.org/10.3390/ma15082955
• 13. Nazemosadat S.M.R., Ghanbarian D., Naderi-Boldaji M., Amin M., (2022). Structural analysis of a mounted moldboard plow using the finite element simulation method. Span. J. Agr. Res. 20 (2), e0204, 14.
• 14. Okuroğullari Y., Çavuşoğlu O., Tutar M., Aydın H., (2022) Investigation of Mechanical Properties of St52 and S460MC Steels Joined by Gas Welding. Int. J. Automot. Technol. 6 (3): 221-225, 2022.
• 15. Ramezani M.A., Yousefi S., Fouladi N., (2017). An experimental and numerical investigation of the effect of geometric parameters on the flexible joint nonlinear. Proc IMechE Part G: J Aerospace Engineering. 0(0) 1–11
• 16. Roodgari M.Z., Jamaati R., Aval H.J. (2020). Microstructure and mechanical properties of IF/St52 steel composite produced by friction stir lap welding. Mater. Sci. Eng. A. 772, 138775.
• 17. Shahverdi M, B. Karbakhsh Ravari B.K., (2021). Investigation of the Effect of Volume Fraction of Martensite and Different Tempering Conditions on the Microstructure and Mechanical Properties of St52 Dual-Phase Steel Used in the Automotive Industry. Journal of Environmental Friendly Materials. Vol. 5, No. 1, 01-05.
• 18. Selamet S., Ozer A.Y.,, Ildan K.E., (2023). Experimental study on the fire performance of prestressed steel parallel wire strands. Eng. Str. 280 , 115709
• 19. Silva L. F. M., Öchsner A., Adams R. D., Handbook of Adhesion Technology, Springer Heidelberg. ISBN 978-3-642-01168-9
• 20. Smith, A., & Johnson, B. (2023). Investigating the Impact of Laser Parameters on Surface Morphology in Fiber Laser Machining. International Journal of Advanced Manufacturing Technology. https://doi.org/10.1007/s00170-023-08867-8
• 21. Thompson, E., & Garcia, F. (2024). Surface Characterization of Steel Alloys Post-Laser Treatment Using Barkhausen Noise Analysis. Materials Science and Engineering A. https://doi.org/10.1016/j.msea.2024.142739
• 22. Valuev D.V., Danilov V.I., Serikbol1 A., Valueva A.V., Research into the Causes of the Cracking of Large Workpieces Low Carbon Steel by Pressure Treatment. Adv. Mater. Res. Vol. 1040. pp 250-255