Experimental investigation of heat transfer performance of different nanofluids in engine cooling system

Yıl 2023, , 144 - 153, 30.12.2023

Tahsin Yüksel , Abdullah Kapıcıoğlu

https://doi.org/10.18245/ijaet.1296361

Öz

Cooling systems are needed for internal combustion engines to operate efficiently. The fluid traditionally used to transfer heat in cooling systems is a mixture of ethylene glycol (EG) and water (W). These fluids generally exhibit an effect that extends the operating temperature range and limits the heat output. On the other hand, nanofluids are known to increase the thermal capacity of liquid suspensions and have been studied in many experimental and numerical studies. This study examines the effects of nanofluids instead of currently used EG-Water on an actual vehicle. Three different nanofluids (TiO2, Al2O3, and SiO2) were used, and the concentration ratios of these fluids were determined as 0.1% and 0.2%. A real vehicle engine cooling system with a volume of 1400 cm3 operating at an average of 2000 rpm was used in the studies. Fluids that are widely studied in the literature were taken into account when selecting nanofluids. The results showed that SiO2 achieved the highest performance, with an increase of 15% compared to the base fluid. On the other hand, it was observed that increasing the concentration value of TiO2 exhibited a lower performance increase compared to other nanofluids. Finally, it has been observed that the operating temperature range of nanofluids affects.

Anahtar Kelimeler

Cooling system, Experimental, Heat transfer rate, Internal combustion engine, Nanofluid

Proje Numarası

TEKNO-026

Kaynakça

• Said Z., Sohail M., Tiwari A.K., “Automotive coolants”, Nanotechnology in the Automotive Industry, 773–792, 2022.
• Bigdeli M.B., Fasano M., Cardellini A., Chiavazzo E., Asinari P., “A review on the heat and mass transfer phenomena in nanofluid coolants with special focus on automotive applications”, Renewable and Sustainable Energy Reviews, 60, 1615–1633, 2016.
• International Energy Agency, “Transport – Topics – IEA”, 2022.
• Said Z., el Haj Assad M., Hachicha A.A., Bellos E., Abdelkareem M.A., Alazaizeh D.Z., et al., “Enhancing the performance of automotive radiators using nanofluids”, Renewable and Sustainable Energy Reviews, 112, 183–194, 2019.
• Tijani A.S., Sudirman A.S. bin., “Thermos-physical properties and heat transfer characteristics of water/anti-freezing and Al2O3/CuO based nanofluid as a coolant for car radiator”, Int J Heat Mass Transf, 118, 48–57, 2018.
• Gupta M., Singh V., Kumar S., Kumar S., Dilbaghi N., Said Z., “Up to date review on the synthesis and thermophysical properties of hybrid nanofluids”, J Clean Prod, 190, 169–192, 2018.
• Alam T., Kim M.H., “A comprehensive review on single phase heat transfer enhancement techniques in heat exchanger applications”, Renewable and Sustainable Energy Reviews, 81, 813–839, 2018.
• Kapıcıoğlu A., Esen H., “Experimental investigation on using Al2O3/ethylene glycol-water nano-fluid in different types of horizontal ground heat exchangers”, Appl Therm Eng., 165, 2020.
• Alous S., Kayfeci M., Uysal A., “Experimental investigations of using MWCNTs and graphene nanoplatelets water-based nanofluids as coolants in PVT systems”, Appl Therm Eng, 162, 114265, 2019.
• Saeed M., Kim M.H., “Heat transfer enhancement using nanofluids (Al2O3-H2O) in mini-channel heatsinks”, Int J Heat Mass Transf, 120, 671–682, 2018.
• Jadar R., Shashishekar K.S., Manohara S.R., “Nanotechnology Integrated Automobile Radiator”, Mater Today Proc, 4(11), 12080–12084, 2017.
• Jadar R., Shashishekar K.S., Manohara S.R., “F-MWCNT Nanomaterial Integrated Automobile Radiator”, Mater Today Proc., 4(10), 11028–11033, 2017.
• Peyghambarzadeh S.M., Hashemabadi S.H., Hoseini S.M., Seifi Jamnani M., “Experimental study of heat transfer enhancement using water/ethylene glycol based nanofluids as a new coolant for car radiators”, International Communications in Heat and Mass Transfer, 38(9), 1283–1290, 2011.
• Hussein A.M., Bakar R.A., Kadirgama K., “Study of forced convection nanofluid heat transfer in the automotive cooling system”, Case Studies in Thermal Engineering, 2, 50–61, 2014.
• Tadepalli R., Gadekula R.K., Reddy K.V., Goud S.R., Nayak S.K., Saini V., et al., “Characterization of Thermophysical properties of Al2O3, TiO2, SiO2, SiC and CuO Nano Particles at Cryogenic Temperatures”, Mater Today Proc., 5(14), 28454–28461, 2018.
• Subhedar D.G., Ramani B.M., Gupta A., “Experimental investigation of heat transfer potential of Al2O3/Water-Mono Ethylene Glycol nanofluids as a car radiator coolant”, Case Studies in Thermal Engineering, 11, 26–34, 2018.
• Ahmed S.A., Ozkaymak M., Sözen A., Menlik T., Fahed A., “Improving car radiator performance by using TiO2-water nanofluid”, Engineering Science and Technology, an International Journal, 21 (5), 996–1005, 2018.
• Peyghambarzadeh S.M., Hashemabadi S.H., Jamnani M.S., Hoseini S.M., “Improving the cooling performance of automobile radiator with Al2O3/water nanofluid”, Appl Therm Eng., 31(10), 1833–1838, 2011.
• Elias M.M., Mahbubul I.M., Saidur R., Sohel M.R., Shahrul I.M., Khaleduzzaman S.S., et al., “Experimental investigation on the thermo-physical properties of Al2O3 nanoparticles suspended in car radiator coolant”, International Communications in Heat and Mass Transfer, 54, 48–53, 2014.
• Nieh H.M., Teng T.P., Yu C.C., “Enhanced heat dissipation of a radiator using oxide nano-coolant”, International Journal of Thermal Sciences, 77, 252–261, 2014.
• M’hamed B., Che Sidik N.A., Akhbar M.F.A., Mamat R., Najafi G., “Experimental study on thermal performance of MWCNT nanocoolant in Perodua Kelisa 1000cc radiator system”, International Communications in Heat and Mass Transfer, 76, 156–161, 2016.
• Li X., Zou C., Qi A., “Experimental study on the thermo-physical properties of car engine coolant (water/ethylene glycol mixture type) based SiC nanofluids”, International Communications in Heat and Mass Transfer, 77, 159–164, 2016.
• Elsebay M., Elbadawy I., Shedid M.H., Fatouh M., “Numerical resizing study of Al2O3 and CuO nanofluids in the flat tubes of a radiator”, Appl Math Model, 40(13–14), 6437–6450, 2016.
• Elsaid A.M., “Experimental study on the heat transfer performance and friction factor characteristics of Co3O4 and Al2O3 based H2O/(CH2OH)2 nanofluids in a vehicle engine radiator”, International Communications in Heat and Mass Transfer, 108, 104263, 2019.
• Muruganandam M., Mukesh Kumar P.C., “Experimental analysis on internal combustion engine using MWCNT/water nanofluid as a coolant”, Mater Today Proc., 21, 248–252, 2020.
• Mukherjee S., Chakrabarty S., Mishra P.C., Chaudhuri P., “Transient heat transfer characteristics and process intensification with Al2O3-water and TiO2-water nanofluids: An experimental investigation”, Chemical Engineering and Processing - Process Intensification, 150, 107887, 2020.
• Chiam H.W., Azmi W.H., Usri N.A., Mamat R., Adam N.M., “Thermal conductivity and viscosity of Al2O3 nanofluids for different based ratio of water and ethylene glycol mixture”, Exp Therm Fluid Sci, 81, 420–429, 2017.
• Tawfik M.M., “Experimental studies of nanofluid thermal conductivity enhancement and applications: A review”, Renewable and Sustainable Energy Reviews, 75, 1239–1253, 2017.
• Oztop H.F., Abu-Nada E., “Numerical study of natural convection in partially heated rectangular enclosures filled with nanofluids”, Int J Heat Fluid Flow, 29(5), 1326–1336, 2008.
• Al-damook, Amer; Alfelleg, Mohanad A.; Khalil W.H., “Three‐dimensional computational comparison of mini pinned heat sinks using different nanofluids: Part one—the hydraulic‐thermal characteristics”, Heat Transfer, 49(1), 441–460, 2020.
• Johansson A., Gunnarsson J., “Predicting Flow Dynamics of an Entire Engine Cooling System Using 3D CFD”, Luleå University of Technology, 2017.
• Che Sidik N.A., Witri Mohd Yazid M.N.A., Mamat R., “Recent advancement of nanofluids in engine cooling system”, Renewable and Sustainable Energy Reviews, 75, 137–144, 2017.
• Holman J.P., Experimental methods for engineers, 8th ed., McGraw-Hill Company, 2012.
• Said Z., el Haj Assad M., Hachicha A.A., Bellos E., Abdelkareem M.A., Alazaizeh D.Z., et al., “Enhancing the performance of automotive radiators using nanofluids”, Renewable and Sustainable Energy Reviews, 112, 183–194, 2019.
• Kakaç S., Pramuanjaroenkij A., “Review of convective heat transfer enhancement with nanofluids”, Int J Heat Mass Transf, 52(13–14), 3187–3196, 2009.