Investigation of mechanical properties of Copper-Graphene composites in terms of production methods and additive ratios: A review

Yıl 2024, Cilt: 42 Sayı: 2, 600 - 613, 30.04.2024

Alper Mutlu , Uğur Çavdar

Öz

Copper (Cu) is a ductile material with excellent electrical and thermal conductivity. It is wide-ly used in many industries including automotive, electronics and electricity. However, the me-chanical properties of copper are relatively poor. Graphene or graphene nanoplatelets (GNPs) have outstanding properties such as high strength, high young modulus, and large surface area. In this way, they significantly change the mechanical properties when used as reinforce-ment in metal matrix composites. In particular, in the field of powder metallurgy (PM), the properties of metallic matrix composites produced with these two materials are still under study. In the production of powdered metal components, the type of additive is important in terms of production cost. As the proportion of additives in the manufactured part increases, the production cost will increase accordingly. This study aims to determine which fabrica-tion methods are used to obtain the highest mechanical properties values with the lowest amount of graphene contribution for Cu-GNP composites. The percentages of additives used in the studies are indicated together with the consolidation and mixing methods to prove the above-mentioned purpose. Thus, it has been determined by which production methods the studies with the highest percentage increase in mechanical properties were produced by using the optimum additive ratio for Cu-GNP metal matrix composites. In this regard, the highest hardness value was obtained with 118% increase percentage, by High pressure torsion method. In another study, Electro-co-deposition method were applied. As a result, the highest tensile strength value increased by 110%. The highest increase in yield strength value was obtained by Spark plasma sintering method with 239%. In addition, the effects of different additives were also examined. Other inferences from the studies are given in the result and discussion section.

Anahtar Kelimeler

Copper, GNP, Composite, Sintering, Powder Metallurgy, Mechanical Properties

Kaynakça

• REFERENCES
• [1] Ngo T-D. Introduction to Composite Materials. London: InTech Open; 2010.
• [2] Ergene B, Bolat Ç. A review of the recent ınvestigation trends in abrasive waterjet cutting and turning of hybrid composites. Sigma J Eng Nat Sci 2019;37:9891016.
• [3] Yalçın B, Ergene B. Analyzing the effect of crack in different hybrid composite materials on mechanical behaviors. Pamukkale Univ J Eng Sci 2018; 24:616–625. [CrossRef]
• [4] Arcaro S, Wermuth TB, Zampiva RYS, Venturini J, ten Caten CS, Bergmann CP, et al. Li2O-ZrO2-SiO2/Al2O3 nanostructured composites for microelectronics applications. J Eur Ceram Soc 2019;39:491– 498. [CrossRef]
• [5] Eveloy V, Rodgers P, Diana A. Performance investigation of thermally enhanced polymer composite materials for microelectronics cooling. Microelectronics J 2015;46:1216–1224. [CrossRef]
• [6] Wang Z, Du C, Qi R, Wang Y. Experimental study on thermal management of lithium-ion battery with graphite powder based composite phase change materials covering the whole climatic range. Appl Therm Eng 2022;216:119072. [CrossRef]
• [7] Santos-Gómez L dos, Cuesta N, Cameán I, García-Granda S, García AB, Arenillas A. A promising silicon/carbon xerogel composite for high-rate and high-capacity lithium-ion batteries. Electrochim Acta 2022;426:140790. [CrossRef]
• [8] Iwao M, Sakurai R, Nakamura H, Hayakawa E, Ohsaki S, Watano S. Solid electrolyte/graphite composite particle for an all-solid-state lithium-ion battery. Adv Powder Technol 2022;33:103633. [CrossRef]
• [9] Tian XK, Xu TX, Yan J, Lin SC, Zhao CY. Designing calcium-looping composites based on lattice energy and phase combination/separation for thermochemical energy storage. Sol Energy Mater Sol Cells 2022;248:111972. [CrossRef]
• [10] Song Z, Ming S, Du K, Zhou C, Wang Y, Xu S, et al. Energy absorption of metal-composite hybrid tubes with a diamond origami pattern. Thin-Walled Struct 2022;180:109824. [CrossRef]
• [11] Pingale AD, Belgamwar SU, Rathore JS. The influence of graphene nanoplatelets (GNPs) addition on the microstructure and mechanical properties of Cu-GNPs composites fabricated by electro-co- deposition and powder metallurgy. Mater Today Proc 2020;28:2062–2067. [CrossRef]
• [12] Fahimi N, Abachi P. The role of powder preparation route on physical and mechanical properties of Cu-rGO bulk nanocomposites. Mater Today Commun 2021;28:102470. [CrossRef] [13] Dong L, Chen W, Deng N, Song J, Wang J. Investigation on arc erosion behaviors and mechanism of W70Cu30 electrical contact materials adding graphene. J Alloys Compd 2017;696:923–930. [CrossRef]
• [14] Raghupathy Y, Kamboj A, Rekha MY, Narasimha Rao NP, Srivastava C. Copper-graphene oxide composite coatings for corrosion protection of mild steel in 3.5% NaCl. Thin Solid Films 2017;636:107–115. [CrossRef]
• [15] Caron RN. Copper Alloys: Properties and Applications. Encyclopedia of Materials: Science and Technology 2001:1665–1668. [CrossRef]
• [16] Aniagor CO, Menkiti MC. Relational description of an adsorption system based on isotherm, adsorption density, adsorption potential, hopping number and surface coverage. Sigma J Eng Nat Sci 2021;38:1073–1098.
• [17] Ciftci H, Er Calıskan C, Aslanhan E, Aktoklu E. Monitoring of heavy metal pollution by using populus nigra and cedrus libani. Sigma J Eng Nat Sci 2021;39:367–373. [CrossRef]
• [18] Tokatlı C. Application of water quality index for drinking purposes in dam lakes: A case study of thrace region. Sigma J Eng Nat Sci 2020;38:393–402.
• [19] Yakamercan E, Aygün A. Ecological risk assessment of domestic sewage sludge: a case study. Sigma J Eng Nat Sci 2021;39:422–433.
• [20] Gunnar F, Nordberg BA, Nordberg M, Friberg LT. Handbook on the Toxicology of Metals. Amsterdam: ScienceDirect; 2007.
• [21] Bloomfield LA. How Things Work: The Physics of Everyday Life. 6th ed. Hoboken, New Jersey: Wiley; 2015.
• [22] Young HD, Sears FW. University Physics. 8th ed. Boston: Addison-Wesley Publication; 1992. [23] Ross RB. Metallic Materials Specification Handbook. 4th ed. Springer; 1992. [CrossRef]
• [24] Nayar A. The metals databook. New York: McGraw-Hill; 1997.
• [25] Dissociation constants of organic acids and bases. Available at: http://www2.chm.ulaval.ca/gecha/chm1903/4_acide-base/organic_acids.pdf. Accessed on Apr 17, 2024.
• [26] Chidhambaram N, Kumari S, Nirmala W, Suyambrakasam G, Thirumurugan A, Udayabhaskar R, et al. WN-PBC, 2022 undefined. ZnO–Sn@ Graphene nanopowders: Integrative impact of tin and graphene on the microstructure, surface morphology, and optical properties. Physica B Condensed Matter 2021;628:413621. [CrossRef]
• [27] Kotov NA. Materials science: Carbon sheet solutions. Nature 2006;442:254–255. [CrossRef]
• [28] Forati T, Sharifi N, Kaydanova T, Ettouil FB, Moghimian N, Pugh M, et al. Wetting and corrosion characteristics of thermally sprayed copper-graphene nanoplatelet coatings for enhanced dropwise condensation application. Carbon Trends 2021;3:100018. [CrossRef]
• [29] Sood AK, Lund I, Puri YR, Efstathiadis H, Pradeep Haldar, Dhar NK, et al. Review of graphene technology and its applications for electronic devices. Available at: https://www.intechopen.com/chapters/49133. Accessed on Apr 17, 2024.
• [30] Hidalgo-Manrique P, Lei X, Xu R, Zhou M, Kinloch IA, Young RJ. Copper/graphene composites: A review. J Mater Sci 2019;54:12236–12289. [CrossRef]
• [31] Prashantha Kumar HG, Anthony Xavior M. Graphene Reinforced Metal Matrix Composite (GRMMC): A Review. Procedia Eng 2014;97:1033–1040. [CrossRef]
• [32] Guler O, Bagci N. A short review on mechanical properties of graphene reinforced metal matrix composites. J Mater Res Technol 2020;9:6808–6833. [CrossRef]
• [33] Sen M. Nanocomposite materials. nanotechnology and the environment. Available at: https://www.intechopen.com/chapters/72636. Accessed on Apr 17, 2024.
• [34] Akkaya E, Çavdar U. Investigation of sintering conditions and the GNP additions on aluminum compacts. Sigma J Eng Nat Sci 2020;38:1977–1986.
• [35] Cavdar U. Graphene Nano platelets reinforced a composite fabricated through Ultra-High frequency induction sintering. Rev Metal 2021;57:e188.
• [36] Malaki M. An Insight into metal matrix composites with nano size reinforcement. Encyclopedia Mater Compos 2021;1:42–51. [CrossRef] [37] Wang X, Li J, Wang Y. Improved high temperature strength of copper-graphene composite material. Mater Lett 2016;181:309–312. [CrossRef]
• [38] Chen F, Ying J, Wang Y, Du S, Liu Z, Huang Q. Effects of graphene content on the microstructure and properties of copper matrix composites. Carbon 2016;96:836–842. [CrossRef]
• [39] Jiang R, Zhou X, Fang Q, Liu Z. Copper-graphene bulk composites with homogeneous graphene dispersion and enhanced mechanical properties. Mater Sci Eng A 2016;654:124–130. [CrossRef]
• [40] Wang T, Zhao R, Zhan K, Bao L, Zhang Y, Yang Z, et al. Preparation of electro-reduced graphene oxide/copper composite foils with simultaneously enhanced thermal and mechanical properties by DC electro-deposition method. Mater Sci Eng A 2021;805:140574. [CrossRef]
• [41] Mathew RT, Singam S, Kollu P, Bohm S, Prasad MJNV. Achieving exceptional tensile strength in electrodeposited copper through grain refinement and reinforcement effect by co-deposition of few layered graphene. J Alloys Compd 2020;840:155725. [CrossRef]
• [42] Shelke AR, Balwada J, Sharma S, Pingale AD, Belgamwar SU, Rathore JS. Development and characterization of Cu-Gr composite coatings by electro-co-deposition technique. Mater Today Proc 2020;28:2090–2095. [CrossRef]
• [43] Sadoun AM, Abdallah AW, Najjar IMR, Basha M, Elmahdy M. Effect of lattice structure evolution and stacking fault energy on the properties of Cu–ZrO2/GNP nanocomposites. Ceram Int 2021;47:29598–29606. [CrossRef]
• [44] Shao Z, Jiang X, Shu R, Wu Z, Huang Z, Deng H, et al. Effect of Cr micro-alloying on microstructure and mechanical properties of alumina whisker and graphene co-reinforced copper matrix composites. J Alloys Compd 2022;909:164804. [CrossRef]
• [45] Han T, Wang F, Li J, He C, Zhao N. Effect of GNPs on microstructures and mechanical properties of GNPs/Al-Cu composites with different heat treatment status. J Mater Sci Technol 2021;92:1–10. [CrossRef]
• [46] Wang J, Guo LN, Lin WM, Chen J, Zhang S, Chen S da, et al. The effects of graphene content on the corrosion resistance, and electrical, thermal and mechanical properties of graphene/copper composites. New Carbon Mater 2019;34:161–169. [CrossRef]
• [47] Li Z, Ni H, Chen Z, Ni J, Chen R, Fan X, et al. Enhanced tensile properties and corrosion resistance of stainless steel with copper-coated graphene fillers. J Mater Res Technol 2020;9:404–412. [CrossRef]
• [48] Li W, Li D, Fu Q, Pan C. Conductive enhancement of copper/graphene composites based on high-quality graphene. RSC Adv 2015;5:80428–80433. [CrossRef]
• [49] Khamaj A, Farouk WM, Shewakh WM, Abu-Oqail AMI, Wagih A, Abu-Okail M. Effect of lattice structure evolution on the thermal and mechanical properties of Cu–Al2O3/GNPs nanocomposites. Ceram Int 2021;47:16511–16520. [CrossRef]
• [50] Shao G, Liu P, Li W, Chen X, Ma F, Liu X, et al. Effects of graphene nanoplates on arc erosion resistance and wear behavior under electric current of copper matrix composites. J Alloys Compd 2020;829:154356. [CrossRef]
• [51] Xian Y, Zou Z, Tu C, Ding Y, Liao T, Zhang F, et al. Identifying the effects of cobalt addition in copper-graphene nanoplatelet composites towards improved tribological performance. J Alloys Compd 2020;835:155444. [CrossRef]
• [52] Dong LL, Fu YQ, Liu Y, Lu JW, Zhang W, Huo WT, et al. Interface engineering of graphene/copper matrix composites decorated with tungsten carbide for enhanced physico-mechanical properties. Carbon NY 2021;173:41–53. [CrossRef]
• [53] Guan C, Zhao Y, Chen G, Kai X, Qian W, Tao R, et al. Synergistic strengthening and toughening of copper coated graphene nanoplates and in situ nanoparticles reinforced AA6111 composites. Mater Sci Eng A 2021;822:141661. [CrossRef]
• [54] Wejrzanowski T, Grybczuk M, Chmielewski M, Pietrzak K, Kurzydlowski KJ, Strojny-Nedza A. Thermal conductivity of metal-graphene composites. Mater Des 2016;99:163–173. [CrossRef]
• [55] Salvo C, Mangalaraja RV, Udayabashkar R, Lopez M, Aguilar C. Enhanced mechanical and electrical properties of novel graphene reinforced copper matrix composites. J Alloys Compd 2019;777:309–316. [CrossRef]
• [56] Kim WJ, Lee TJ, Han SH. Multi-layer graphene/copper composites: preparation using high-ratio differential speed rolling, microstructure and mechanical properties. Carbon NY 2014;69:55–65. [CrossRef]
• [57] Dutkiewicz J, Ozga P, Maziarz W, Pstruś J, Kania B, Bobrowski P, et al. Microstructure and properties of bulk copper matrix composites strengthened with various kinds of graphene nanoplatelets. Mater Sci Eng A 2015;628:124–134. [CrossRef]
• [58] Li JF, Zhang L, Xiao JK, Zhou KC. Sliding wear behavior of copper-based composites reinforced with graphene nanosheets and graphite. Trans Nonferrous Met Soc China 2015;25:3354–3362. [CrossRef]
• [59] Wei BW, Qu D, Hu CF, Li FZ, Zhou TL, Xie RJ, et al. Synthesis and physical properties of graphene nanosheets reinforced copper composites. Adv Mat Res 2014;833:310–314. [CrossRef]
• [60] Khobragade N, Kumar B, Bera S, Roy D. Studies on graphene reinforced Cu base composites prepared by two step thermal processing method. Mater Today Proc 2017;4:8045–8051. [CrossRef]
• [61] Qu D, Li FZ, Zhang HB, Wang Q, Zhou TL, Hu CF, et al. Preparation of graphene nanosheets/copper composite by spark plasma sintering. Adv Mat Res 2014;833:276–279. [CrossRef]
• [62] Chu K, Wang XH, Li YB, Huang DJ, Geng ZR, Zhao XL, et al. Thermal properties of graphene/metal composites with aligned graphene. Mater Des 2018;140:85–94. [CrossRef]
• [63] Chu K, Wang F, Wang XH, Huang DJ. Anisotropic mechanical properties of graphene/copper composites with aligned graphene. Mater Sci Eng A 2018;713:269–277. [CrossRef]
• [64] Chu K, Wang XH, Wang F, Li YB, Huang DJ, Liu H, et al. Largely enhanced thermal conductivity of graphene/copper composites with highly aligned graphene network. Carbon NY 2018;127:102–112. [CrossRef]
• [65] Jiang R, Zhou X, Liu Z. Electroless Ni-plated graphene for tensile strength enhancement of copper. Mater Sci Eng A 2017;679:323–328. [CrossRef]
• [66] Ghodrati H, Ghomashchi R. Effect of graphene dispersion and interfacial bonding on the mechanical properties of metal matrix composites: an overview. FlatChem 2019;16:100113. [CrossRef]
• [67] Zhang D, Zhan Z. Preparation of graphene nanoplatelets-copper composites by a modified semi-powder method and their mechanical properties. J Alloys Compd 2016;658:663–671. [CrossRef]
• [68] Kim MJ, Cruz MA, Ye S, Gray AL, Smith GL, Lazarus N, et al. One-step electrodeposition of copper on conductive 3D printed objects. Addit Manuf 2019;27:318–326. [CrossRef]
• [69] Guo S, Zhang X, Shi C, Liu E, He C, He F, et al. In situ synthesis of high content graphene nanoplatelets reinforced Cu matrix composites with enhanced thermal conductivity and tensile strength. Powder Technol 2020;362:126–134. [CrossRef]
• [70] Ali S, Ahmad F, Yusoff PSMM, Muhamad N, Oñate E, Raza MR, et al. A review of graphene reinforced Cu matrix composites for thermal management of smart electronics. Compos Part A Appl Sci Manuf 2021;144:106357. [CrossRef]
• [71] Zhao S, Zhao Z, Yang Z, Ke LL, Kitipornchai S, Yang J. Functionally graded graphene reinforced composite structures: a review. Eng Struct 2020;210:110339. [CrossRef]
• [72] Iqbal AA, Sakib N, Iqbal AKMP, Nuruzzaman DM. Graphene-based nanocomposites and their fabrication, mechanical properties and applications. Materialia (Oxf) 2020;12:100815. [CrossRef]
• [73] Chen Y, Zhang X, Liu E, He C, Han Y, Li Q, et al. Fabrication of three-dimensional graphene/Cu composite by in-situ CVD and its strengthening mechanism. J Alloys Compd 2016;688:69–76. [CrossRef]
• [74] Cao M, Xiong DB, Tan Z, Ji G, Âmin-Ahmadi B, Guo Q, et al. Aligning graphene in bulk copper: nacre-inspired nanolaminated architecture coupled with in-situ processing for enhanced mechanical properties and high electrical conductivity. Carbon NY 2017;117:65–74. [CrossRef]
• [75] Zhao C, Wang J. Fabrication and Tensile properties of graphene/copper composites prepared by electroless plating for structrual applications. PSS Appl Mater Sci 2014;211:2878–2885. [CrossRef]
• [76] Chu K, Jia C. Enhanced strength in bulk graphene–copper composites. PSS Appl Mater Sci 2014;211:184–190. [CrossRef]
• [77] Khobragade N, Sikdar K, Kumar B, Bera S, Roy D. Mechanical and electrical properties of copper-graphene nanocomposite fabricated by high pressure torsion. J Alloys Compd 2019;776:123–132. [CrossRef]
• [78] Ayyappadas C, Muthuchamy A, Raja Annamalai A, Agrawal DK. An investigation on the effect of sintering mode on various properties of copper-graphene metal matrix composite. Adv Powder Technol 2017;28:1760–1768. [CrossRef]
• [79] Pavithra CLP, Sarada B v., Rajulapati K v., Rao TN, Sundararajan G. A New Electrochemical approach for the synthesis of copper-graphene nanocomposite foils with high hardness. Sci Rep 2014;4:4049. [CrossRef]
• [80] Si X, Li M, Chen F, Eklund P, Xue J, Huang F, et al. Effect of carbide interlayers on the microstructure and properties of graphene-nanoplatelet-reinforced copper matrix composites. Mater Sci Eng A 2017;708:311–318. [CrossRef]
• [81] Zhang D, Zhan Z. Strengthening effect of graphene derivatives in copper matrix composites. J Alloys Compd 2016;654:226–233. [CrossRef]
• [82] Li M, Che H, Liu X, Liang S, Xie H. Highly enhanced mechanical properties in Cu matrix composites reinforced with graphene decorated metallic nanoparticles. J Mater Sci 2014;49:3725–3731. [CrossRef]
• [83] Gao X, Yue H, Guo E, Zhang H, Lin X, Yao L, et al. Mechanical properties and thermal conductivity of graphene reinforced copper matrix composites. Powder Technol 2016;301:601–607. [CrossRef]
• [84] Chen Y, Zhang X, Liu E, He C, Shi C, Li J, et al. Fabrication of in-situ grown graphene reinforced Cu matrix composites. Sci Rep 2016;6:19363. [CrossRef]
• [85] Zhang K, Shao G, Chen X, Li W, Ma F, Liu P. Study of mechanical properties of graphene nanoplates reinforced copper matrix composites prepared through electrostatic self-assembly and electroless copper plating. Mater Lett 2019;252:338–341. [CrossRef]
• [86] Shu S, Zhang Q, Ihde J, Yuan Q, Dai W, Wu M, et al. Surface modification on copper particles toward graphene reinforced copper matrix composites for electrical engineering application. J Alloys Compd 2022;891:162058. [CrossRef]
• [87] Han X, Yang L, Zhao N, He C. Copper-coated graphene nanoplatelets-reinforced Al–Si alloy matrix composites fabricated by stir casting method. Acta Metall Sin (Engl Lett) 2020;34:111–124. [CrossRef]
• [88] Tan W, Jiang X, Shao Z, Sun H, Fang Y, Shu R. Fabrication and mechanical properties of nano carbon reinforced laminated Cu matrix composites. Powder Technol 2022;395:377–390. [CrossRef]
• [89] Naseer A, Ahmad F, Ali S, Haider W. Powder injection molded nano copper oxide grafted graphene reinforced copper matrix composites. Powder Technol 2022;397:117101. [CrossRef]
• [90] Shi L, Liu M, Yang Y, Liu R, Zhang W, Zheng Q, et al. Achieving high strength and ductility in copper matrix composites with graphene network. Mater Sci Eng A 2021;828:142107. [CrossRef]
• [91] Yang T, Chen W, Zhang H, Ma L, Fu YQ. In-situ generated graphene from wheat flour for enhancing mechanical and electrical properties of copper matrix composites. Mater Sci Eng A 2022;835:142662. [CrossRef]
• [92] Shi L, Liu M, Zhang W, Ren W, Zhou S, Zhou Q, et al. Interfacial design of graphene nanoplate reinforced copper matrix composites for high mechanical performance. JOM 2022;74:3082–3090. [CrossRef]
• [93] Jeong HK, Yun. PL, Lahaye RJWE, Park MH, Kay HA, Ick JK, et al. Evidence of graphitic AB stacking order of graphite oxides. J Am Chem Soc 2008;130:1362–1366. [CrossRef]