COMPARISION OF INTERNATIONAL CODES FOR STEEL ANCHORS DETAILS USING IN SEISMIC STRENTHENING

Yıl 2016, Cilt: 4 Sayı: 3, 216 - 230, 01.09.2016

Musa Hakan Arslan , Mohamud Abdirahman Ibrahım

https://doi.org/10.15317/Scitech.2016320517

Öz

Having poor seismic performance reinforced concrete frame must be strengthened to reach sufficient seismic performance. The main factor that affects the seismic performance, designing and application of the anchor dowels in the connection zone of infill shear wall and weak reinforced frame. Connection between the frame and the infill wall are usually achieved by using dowels that are placed in the holes drilled into inner faces of the frame members, and fixed by a resin. In this study, the design and detailing guidelines for the design of the post-installed anchors in TEC (2007), ACI 318, JCI (2001) and IS15988 have been compared. According to the results, in ACI 318-14, the shear capacity of anchors is effected by embedment depth, anchor bar diameter, concrete strength, strength of the bar and edge distance. In TEC-2007, shear strength is affected only by two properties of the anchor bar: strength and diameter. JCI-2001 design code considers the two factors outlined in TEC-2007 and concrete strength. Based on the comparison conducted in this study, there are insufficient guidelines in TEC-2007 for the design and detailing of anchor bars that are typically used as connection between an existing frame and new RC infill wall.

Anahtar Kelimeler

Infill walls, Post-installed anchors, Strengthening, Shear capacity

Sismik Güçlendirmede Kullanılan Ankraj Detayları İçin Uluslararası Yönetmeliklerin Karşılaştırılması

Öz

Deprem performansı yetersiz olan betonarme çerçevelerin yeterli performans seviyesine gelebilmesi için betonarme perde duvarlar ile güçlendirilmesi gerekmektedir. Sonradan yapılan betonarme perde duvarların davranışını etkileyen en önemli unsur çerçeve ve betonarme duvar arasında bağlantı olarak kullanılan ankrajların tasarımı ve uygulamasıdır. Çerçeve ve betonarme dolgu duvarlar arasındaki bağlantı genellikle çerçeve parçalarının iç yüzeylerine açılan deliklere yerleştirilen ankraj donatılarının reçine ile sabitlenmesiyle elde edilir. Bu çalışmada ankrajlar için TEC–2007, ACI 318–14, JCI–2001 ve IS1–5988 gibi yönetmeliklerde verilen tasarım kuralları karşılaştırılmıştır. Yapılan karşılaştırmaya göre ACI 318-14’te, ankrajların kesme dayanımının gömme derinliği, donatı çapı, beton dayanımı, ankraj donatı dayanımı ve kenar mesafesi ile ilişkili olduğu görülmüştür. TEC-2007’de ise ankrajların kesme dayanımı sadece ankraj donatısının çekme dayanımı ve ankraj çapından etkilendiğinden bahsedilmektedir. ISI–5988, JCI-2001’in TEC- 2007’ gibi beton basınç dayanımına dikkat ettiği görülmüştür. Bu çalışmada dört yönteminde kıyaslanması sonucunda, mevcut çerçeve ve yeni betonarme dolgu duvar arasında bağlantı olarak kullanılan ankrajlar için TEC-2007’nin yetersiz kaldığı görülmüştür.

Anahtar Kelimeler

Perde duvar, Ankraj, Güçlendirme, Kesme kapasitesi

Kaynakça

• ACI Committee, 2014, Building Code Requirements for Structural Concrete and Commentary (ACI 318-14), American Concrete Institute.
• Altin, S., Ersoy U., Tankut T., 1992,“Hysteretic Response of Reinforced-Concrete Infilled Frames”,ASCE Journal of Structural Engineering, Vol.118(8), pp.2133–2150.
• Altin, S., Anil O., Kara E., 2008, “An Experimental Study on Reinforced Concrete Partially Infilled Frames”, Engineering Structures, Vol. 29,pp.449–460.
• Anil, O., Altin, S., 2007, “An Experimental Study on Reinforced Concrete Partially Infilled Frames”, Engineering Structures, Vol. 29, pp.449-460.
• Çalışkan, Ö.,Yilmaz, S., and Kaplan, H., 2011, “Güçlendirme Ankrajlarının Kesme Dayanımının ACI318 ve TS500’e Göre Belirlenmesi”, Journal of Engineering Sciences, Vol. 14(3), pp. 19-27.
• Çalışkan, Ö., Yılmaz S., Kaplan H., Kıraç N., 2013, “Shear Strength of Epoxy Anchors Embedded Into Low Strength Concrete”, Construction and Building Materials, Vol. 38, pp. 723-730.
• Canbay, E., Ersoy, U.,Ozcebe, G., 2003, “Contribution of Reinforced Concrete Infillsto Seismic Behavior of Structural Systems”, ACI Structural Journal, Vol.100(5), pp. 637-643.
• Canbay, E., 2001, Contribution of RC Infills to The Seismic Behavior of Structural Systems, PhD Dissertation, Middle East Technical University, Ankara.
• Canbay, E., Ersoy U., Özcebe G., 2002, “Betonarme Dolgu Duvarların Yapıların Sismik Davranışı Üzerine Etkileri. Research Report No: INTAG 563”, Scientific and Technical Research Council of Turkey-TUBITAK, Ankara.
• CEN, EN 1998-3:2005 Eurocode 8: Design of structures for earthquake resistance - Part 3: Assessment and retrofitting of buildings. European Committee of Standardization. Brussels.
• Erdem, I., Akyuz, U., Ersoy, U. and Ozcebe, G., 2006, “Experimental and Analytical Studies on The Strengthening of Rc
• Frames”, 13th World Conference on Earthquake Engineering, Vancouver, Canada.
• Ersoy, U., 1992, “Repair and Strengthening of RC Structures”, International Symposium on Earthquake Disaster Prevention, CENAPRED, Mexico City, pp. 123-138.
• Fardis M., Schetakis, A., Strepelias, E., 2013, “RC Buildings Retrofitted by Converting Frame Bays Into RC Walls”, Bull Earthquake Eng.,Vol. 11, pp. 1541–1561.
• Gesoğlu M., Özturhan T., Özel M., Güneyişi E., 2005, “Tensile Behavior Of Post-Installed Anchors in Plain and Steel Fiber-Reinforced Normal-And High-Strength Concretes”, ACI Structural Journal, Vol. 102 (2), pp. 224-231.
• Hayashi, T., Niwa, H. and Fukuhara, M., 1980, “The Strengthening Methods of the Existing Reinforced Concrete Buildings”, 7th World Conference on Earthquake Engineering, Istanbul, Vol.7, pp.89-96.
• IS 15988, 2013, Seismic Evaluation and Strengthening of Existing Reinforced Concrete Buildings – Guidelines, New Delhi.
• Jirsa, J.O., 1988, “Behaviour of Epoxy-Grouted Dowels and Bolts Used for Repair of Strengthening of RC Structures”, Proceedings of 9th World Conference on Earthquake Engineering, Tokyo-Kyoto, pp.371-376, 1988.
• JCI, 2001, Standard for Seismic Evaluation of Existing Reinforced Concrete Buildings, Japan Building Disaster Prevention Association.
• Obata, M., Inoue, M., Goto, Y., 1998, “The Failure Mechanism and The Pull-Out Strength of A Bond-Type Anchor Near A Free Edge”,Mechanics of Materials, Vol. 28 (1-4), pp. 113-122.
• Sonuvar, M., Ozcebe, G. and Ersoy, U., 2004, “Rehabilitation of Reinforced Concrete Frames with Reinforced Concrete Infills”, ACI Structural Journal, Vol. 101 (4), pp. 494-500.
• Phan, T., Cheok, S., and Todd, R., 1996, Strengthening Methodology for Lightly Reinforced Concrete Frames: Recommended Design Guidelines for Strengthening with Infill Walls. Gaithersburg: National Institute of Standards and Technology.
• Sakla, S.S.S., Ashour, A.F., 2005,“Prediction of Tensile Capacity of Single Adhesive Anchors Using Neural Networks”, Computers and Structures, Vol. 83 (21-22), pp. 1792-1803.
• Strepelias, E., Palios, X., Bousias, N. and Fardis, N., 2012, “Pseudodynamic Tests on 4-Storey Nonductile Frames with RC Infilling of The Bay”, SERIES Workshop: Role of Research Infrastructures in Seismic Rehabilitation, Istanbul, 2012.
• Sugano, S., 1981, “Seismic Strengthening of Existing Reinforced Concrete Buildings in Japan”, Bulletin of the New Zealand National Society for Earthquake Engineering, Vol. 14(4), pp. 371-378.
• TEC-2007, Ministry of Public Works and Settlement, Turkish Earthquake Code-2007: Specifications For Buildings to Be Built in Seismic Areas, Ankara, Turkey (in Turkish), 2007.
• TS500 Betonarme Yapıların Hesap ve Yapım Kuralları, 2000, Türk Standartları Enstitüsü, Ankara.
• Turk, M., Ersoy, U., Ozcebe, G., 2003, “Seismic Rehabilitation of RC Frames with RC Infill Walls”, Fifth National Conference on Earthquake Engineering, Istanbul-Turkey, pp. 1-9, 2003.
• Yilmaz C., Aktas M., Kuyuk S., Yaman D., 2014, “Behavior of RC Frames Strengthened with Infill Panel under Dynamic Loading”, Second European Conference on Earthquake Engineering and Seismology, Istanbul-Turkey, pp.861–866, 2014.
• Yilmaz S., Özen M.A., Yardim Y., 2013, “Tensile behavior of post-installed chemical anchors embedded to low strength concrete”, Construction and Building Materials,Vol. 47, pp. 861-866.