EFFECT OF CARBON FIBER ADDITIVE ON TENSILE PROPERTIES OF LARGE SCALE ADDITIVE MANUFACTURED (LSAM) ABS SINGLE WALL PARTS

Yıl 2023, Cilt: 6 Sayı: 2, 79 - 82, 31.12.2023

Ömer Eyercioğlu , Engin Tek , Mehmet Ali Akeloğlu , Mehmet Aladag

Öz

Additive Manufacturing (AM) is one of the most studied technologies to produce different parts today. Large-scale additive manufacturing (LSAM) is used to produce complex parts without further technological processes and for the production of large-sized polymer parts. In order for the parts produced from polymer materials to show better mechanical properties, a range of different materials is required. In this study, the tensile properties of 3D printed ABS single wall parts using LSAM were investigated experimentally. The effect of carbon fiber (0, 5%, and 10%) additive on the main mechanical properties of ABS was investigated. The tests were carried out according to ASTM D638 standards as the spatial printing direction (0⁰ and 90⁰). According to the results of the tensile test, ABS material reinforced with 5% carbon fiber showed higher load resistance than other mixture ratios. In all groups, it was observed that the samples with a horizontal (0⁰) orientation compared to the printing direction showed better performance.

Anahtar Kelimeler

Additive Manufacturing (AM), Large Scale Additive Manufacturing (LSAM), Acrylonitrile Butadiene Styrene (ABS), Tensile Strength., Carbon Fiber

Kaynakça

• Zhao, Y., Chen, Y., and Zhou, Y. Novel mechanical models of tensile strength and elastic property of FDM AM PLA materials: Experimental and theoretical analyses. Materials and Design, (2019), 181, 108089.
• Wang, X., Zhao, L., Fuh, J.Y.H., and Lee, H.P. Effect of porosity on mechanical properties of 3D printed polymers: Experiments and micromechanical modeling based on X- ray computed tomography analysis. Polymers, (2019), 11 (7).
• Rodríguez-Panes, A., Claver, J., and Camacho, A.M. The influence of manufacturing parameters on the mechanical behaviour of PLA and ABS pieces manufactured by FDM: A comparative analysis. Materials, (2018), 11 (8).
• Sehhat, M.H., Mahdianikhotbesara, A., and Yadegari, F. Verification of stress transformation in anisotropic material additively manufactured by fused deposition modeling (FDM). International Journal of Advanced Manufacturing Technology, (2022), 123 (5–6), 1777–1783.
• Movahedi, N., and Linul, E. Quasi-static compressive behavior of the ex-situ aluminum-alloy foam-filled tubes under elevated temperature conditions. Materials Letters, (2017), 206, 182–184.
• Rajak, D.K., Pagar, D.D., Menezes, P.L., and Linul, E. Fiber-reinforced polymer composites: Manufacturing, properties, and applications. Polymers, (2019), 11 (10).
• Bhalodi, D., Zalavadiya, K., and Gurrala, P.K. Influence of temperature on polymer parts manufactured by fused deposition modeling process. Journal of the Brazilian Society of Mechanical Sciences and Engineering, (2019), 41 (3), 1–11.
• Kurfess, R. A thermally-driven design methodology for large-scale polymer additive manufacturing systems. (2017).
• Roschli, A., Duty, C., Lindahl, J., Post, B.K., Chesser, P.C., Love, L.J., and Gaul, K.T. Increasing interlaminar strength in large scale additive manufacturing. Solid Freeform Fabrication 2018: Proceedings of the 29th Annual International Solid Freeform Fabrication Symposium - An Additive Manufacturing Conference, SFF 2018, (2020), 543–555.
• Eyercioğlu, Ö., Aladağ, M., and Sever, S. Temperature Evaluation and Bonding Quality of Large Scale Additive Manufacturing Thin Wall Parts. Sigma J Eng & Nat Sci, (2018), 36 (3), 645–654.
• EYERCİOĞLU, Ö., Engin, T.E.K., ALADAĞ, M., and Gülağa, T.A.Ş. Effect of different amounts of carbon fiber additive ABS on thermal distortion and cooling time. The International Journal of Materials and Engineering Technology, (2022), 5 (1), 13–17.
• Eyercioglu, O., Tek, E., Aladag, M., and Tas, G. 4-Effect of Different Amounts of Carbon Fiber Additive Abs on Thermal Distortion and Cooling Time. (2022), 5, 13–17.
• Lee, C.S., Kim, S.G., Kim, H.J., and Ahn, S.-H. Measurement of anisotropic compressive strength of rapid prototyping parts. Journal of materials processing technology, (2007), 187, 627–630.
• Weng, Z., Wang, J., Senthil, T., and Wu, L. Mechanical and thermal properties of ABS/montmorillonite nanocomposites for fused deposition modeling 3D printing. Materials & Design, (2016), 102, 276–283.
• Thomas, J.P., and Renaud, J.E. Mechanical behavior of acrylonitrile butadiene styrene (ABS) fused deposition materials . Experimental investigation Âguez. (2006), 7 (3), 148–158.
• Kartal, F., Kaptan A. Mechanical performance of salvadora persical (Miswak) reinforced polylactic acid matrix composites for three dimensional printing. BSJ Eng Sci, (2023), 6(4): 458-468.
• Kartal, F. , Kaptan, A. Investigating the effect of nozzle diameter on tensile strength in 3D-printed polylactic acid parts. BSJ Eng Sci. (2023), 6(3): 276- 282.
• Kaptan, A., Kartal, F. The effect of fill rate on mechanical properties of pla printed samples. Igdır University Journal of the Institute of Science and Technology (2020), 10(3): 1919-1927.