Implications of Higher Mode Effects on Seismic Shear Demand of Eccentrically Braced Frames with Short Link Beam

Yıl 2025, Cilt: 36 Sayı: 4

Ahmet Metin Yildirim , Bilge Doran , Yasin Fahjan

https://doi.org/10.18400/tjce.1540861

Öz

The capacity design philosophy primarily focuses on limiting the seismic shear force that will affect the structural system and has been widely accepted in the structural earthquake engineering community. However, several sources in the literature indicate that there are still some problematic points in this design philosophy. The main problem is that the proposed solution in this philosophy considers the first fundamental mode of the structural system but overlooks the effects of higher modes. This problem may lead to increased seismic shear force demand that is attempted to be limited by the capacity design philosophy. A similar problem with cantilever walls was first identified in the mid-1970s, and several solutions, which consider both dynamic effects and capacity design principles, were proposed in the relevant literature. Regarding Eccentrically Braced Frames (EBFs) with short link beam, no specific study on the dynamic amplification of shear force demand has been observed in the literature. However, other studies in different contexts have alluded to the possibility of such a phenomenon in EBFs and other steel frames. This study focuses on the dynamic amplification of shear force demands and determines its range using incremental dynamic analysis and multi-modal pushover analyses. Consequently, it has been demonstrated that limiting the shear force demand of the system, as recommended by the capacity design principles in all steel structure design specifications, is not possible. The use of a dynamic amplification factor is suggested to address non-ductile failure modes and enhance structural reliability. In this context, the current study examines the previously mentioned issue for eccentrically braced frames with short link beam in 4-story and 8-story buildings, representing low-rise and mid-rise buildings respectively. As a result, the seismic shear demands for EBFs found in Incremental Dynamic Analysis are significantly higher than those calculated by using capacity design principles for both 4-story and 8-story buildings. Additionally, the results from Incremental Dynamic Analysis have been comparatively examined with multi-modal pushover analyses. The internal force demands for elements of EBFs, especially in braces, increased due to the higher base shear demands, excluding the link beam.

Anahtar Kelimeler

Eccentrically braced frames with short link beam, seismic shear demand, push-over analysis, incremental dynamic analysis, higher mode effects, incremental response spectrum analysis

Kaynakça

• ANSI/AISC 341-10 (2010), Seismic provisions for structural steel buildings, American Institute of Steel Construction: Chicago, IL, USA.
• Blakeley, R.W.G., Cooney, R.C. and Megget, L.M. (1975), “Seismic shear loading at flexural capacity in cantilever wall structures.” Bull. of the NZ Soc. for Earthquake Eng., 8(4), 278-290.
• Rutenberg A. (2013), “Seismic shear forces on RC walls: review and bibliography.” B. Earthq. Eng. 11(5), 1727-1751. https://doi.org/10.1007/s10518-013-9464-1
• Fujimoto M., Aoyagi T., Ukai K., Wada A. and Saito K. (1972), "Structural characteristics of eccentric K-Braced frames," Tans. Arch. Inst. Jap., 195(), 39-49, (in Japanese)
• Tanabashi, R., Naneta, K. and Ishida, T. (1974), “On the rigidity and ductility of steel bracing assemblage”, Proceedings of the 5th World Conference on Earthquake Engineering, Rome, Italy.
• Roeder C.W. and Popov E.P. (1977), “Inelastic Behavior of Eccentrically Braced Steel Frames Under Cyclic Loading”, Report No. UCB/EERC-77/18, University of California, Berkeley, CAL, USA.
• Roeder, C.W.; Popov, E.P., (1978), “Eccentrically braced steel frames for earthquakes”, Journal of the Structural Division, 104(ST3),391-412.
• Roeder, C.W., Popov, E.P., (1978), “Cyclic shear yielding of wide flange Beams”, J. Eng. Mech. Div., 104(4):763-780.
• Roeder, C.W., Foutch, D.A., Goel, S.C. (1987), “Seismic testing of full-scale steel building-part II”, J. Struct. Eng., 113(11):2130 2145. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:11(2130)
• Hjelmstad K.D., Popov, E.P., (1983), “Cyclic behavior and design of link beams”, J. Struct. Eng., 109(10):2387-2403. https://doi.org/10.1061/(ASCE)0733-9445(1983)109:10(2387)
• Malley, J.O.; Popov, E.P., (1984), “Shear Links in Eccentrically Braced Frames”, J. Struct. Eng., 110(9), 2275-2295. https://doi.org/10.1061/(ASCE)0733-9445(1984)110:9(2275)
• Kasai, K.; Popov, E.P., (1986(a)), “Cyclic web buckling control for shear link beams”, J. Struct. Eng., 112(3),505-523. https://doi.org/10.1061/(ASCE)0733-9445(1986)112:3(505)
• Kasai, K.; Popov, E.P., (1986(b)), “General behavior of WF steel shear link beams”, J. Struct. Eng., 112(2),362-382. https://doi.org/10.1061/(ASCE)0733-9445(1986)112:2(362)
• Ricles, J.M.; Popov, E.P., (1989), “Composite action in eccentrically braced frames”, J. Struct. Eng., 115(8), 2046-2066. https://doi.org/10.1061/(ASCE)0733-9445(1989)115:8(2046)
• Okazaki T., Arce G., Ryu H.C. and Engelhardt M.D. (2005), "Experimental study of local buckling, overstrength, and fracture of links in eccentrically braced frames", J. Struct. Eng., 131(10), 1526-1535. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:10(1526)
• Richards, P.W. and Uang, C.M., (2005), “Effect of flange width thickness ratio on eccentrically braced frames link rotation capacity”, J. Struct. Eng., 131(10), 1546-1552. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:10(1546)
• Dusicka P., Itani A.M. and Buckle I.G. (2010), “Cyclic behavior of shear links of various grades of plate steel”, J. Struct. Eng.,136(4), 370-378. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000131
• Ashtari, A. and Erfani, S. (2016), “An analytical model for shear links in eccentrically braced frames”, Steel Compos. Struct., Int. J., 22(3), 627-645. https://doi.org/10.12989/scs.2016.22.3.627
• Lian, M., Su, M. and Guo, Y. (2015), “Seismic performance of eccentrically braced frames with high strength steel combination”, Steel Compos. Struct., Int. J., 18(6), 1517-1539. https://doi.org/10.12989/scs.2015.18.6.1517
• Caprili, S., Mussini, N. and Salvatore, W. (2018), “Experimental and numerical assessment of EBF structures with shear links”, Steel Compos. Struct., Int. J., 28(2), 123-138. https://doi.org/10.12989/scs.2018.28.2.123
• Li, T., Su, M. and Sui, Y. (2020), “Spatial substructure hybrid simulation tests of high-strength steel composite Y-eccentrically braced frames”, Steel Compos. Struct., Int. J., 34(5), 715-723-1539.https://doi.org/10.12989/scs.2020.34.5.715
• Stratan A. and Dubina D. (2004), “Bolted links for eccentrically braced steel frames”,Proceedings of the 5th AISC/ECCS International Workshop: Connections in Steel Structures V. Behaviour, Strength and Design, Delft, The Netherlands, June.
• Mansour, N., Christopoulos, C. and Tremblay R. (2011), “Experimental validation of replaceable shear links for eccentrically braced steel frames”, J. Struct. Eng., 137 (10)1141-1152. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000350
• Fussell A.J., Cowie K.A., Clifton G.C., and Mago N. (2014), “Development and research of eccentrically braced frames with replaceable active links”, Proceedings of the 2014 NZSEE Conference, Auckland, New Zealand, March.
• Bozkurt, M. B. And Topkaya, C. (2017), “Replaceable links with direct brace attachments for eccentrically braced frames”, Eartq. Eng. Struct. D., 46(13), pp.2121-2139. https://doi.org/10.1002/eqe.2896
• Popov, E.P., Kasai, K. and Ricles, J.M. (1992), “Methodology for optimum EBF link design”, Earthquake Engineering Tenth World Conference, Madrid, Spain, July.
• Bosco, M., Rossi, P.P. (2009), “Seismic behavior of eccentrically braced frames”, Eng. Struct., 31(3), 664-674. https://doi.org/10.1016/j.engstruct.2008.11.002
• Crişan, A., Staratan, A. (2009), “Overstrength demands in multistorey eccentrically braced frames”, Proceedings of the 11th WSEAS International Conference on Sustainability in Science Engineering, Timisoara, Romania, May.
• Koboevic, S., Rozon, J. and Tremblay R. (2012), “Seismic performance of low-to-moderate height eccentrically braced steel frames designed for North American seismic conditions”, J. Struct. Eng., 138(12),1465-1476, 2012.
• Koboevic, S. and David, S.O.J. (2010), “Design and seismic behavior of taller eccentrically braced frames”, Can. J. Civ. Eng., 37(2), 195-208. https://doi.org/10.1139/L09-131
• Chen, L., Tremblay, R. and Tirca, L. (2012), “Seismic performance of modular braced frames for multi-story building applications”, Earthquake Engineering, 15. World Conference of Earthquake Engineering, Lisboa, Portugal, September.
• Chen, L., Tremblay R. and Tirca L. (2014), “Enhancing the seismic performance of multi-story buildings with a modular tied braced frame system with added energy dissipating devices”, International Journal of High-Rise Buildings, 3(1), 21-33.
• Kuşyılmaz A. and Topkaya C. (2016), “Evaluation of seismic response factors for eccentrically braced frames using FEMA P695 methodology”, Earthq. Spectra 32(1) 303-321. https://doi.org/10.1193/071014EQS097M
• Qi, Y., Li, W. and Feng, N. (2017), “Seismic collapse probability of eccentrically braced steel frames”, Steel Compos. Struct., Int. J., 24(1), 37-52. https://doi.org/10.12989/scs.2017.24.1.037
• Clifton, C., Bruneau, M., MacRae, G., Leon, R., and Fussell, A. (2011), “Steel structures damage from the Christchurch earthquake of February 22, 2011, NZST.”, Bull. New Zealand Soc. Earthquake Eng., 44(4), 297-318.
• Gardiner G., Clifton C., and MacRae G.A. (2013), “Performance, damage assessment and repair of a multistory eccentrically braced frame building following the Christchurch earthquake series”, Proceedings of the Steel Innovations Conference 2013, Christchurch, New Zealand, February.
• Simpson B. (2020), “Higher‐mode force response in multi‐story strongback‐braced frames”, Earthquake Engineering and Structural Dynamics, 49(14), 1406-1427.
• MacRae, G. (1989), “The seismic response of steel frames” Ph.D. Dissertation, University of Canterbury, Christchurch.
• Harris, J.L., Speicher, M.S. (2015) “Assessment of first-generation performance-based seismic design methods for new steel buildings. Eccentrically braced frames” Report no. NIST.TN.1863-3, National Institute of Standards and Technology, Gaithersburg, MD,USA.
• Richards, P.W.(2009), "Seismic column demands in ductile braced frames", J. Struct. Eng., 135(1), 33-41. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:1(33)
• ASCE/SEI (2006), Seismic Rehabilitation of Existing Buildings, Structural Engineering Institute of the American Society of Civil Engineers; Reston, VA, USA.
• ASCE 7 (2010), Minimum Design Loads for Buildings and Other Structures, American Society of Civil Engineers and Structural Engineering Institute, Reston, VA, USA.
• ANSI/AISC 360-10 (2010), Specification for Structural Steel Buildings; American Institute of Steel Construction, Chicago, IL, USA.
• Speicher, M.S. and Harris, J.L., (2016), “Collapse prevention seismic performance assessment of new eccentrically braced frames using ASCE 41”, Eng. Struct., 117, 344-357. https://doi.org/10.1016/j.engstruct.2016.02.018
• Bruneau M., Uang C.M., and Sabelli R. (2011), Ductile Design of Steel Structures, McGrawHiil, New York, NY, USA.
• PERFORM 3D (2018), Nonlinear Analysis and Performance Assessment for 3D Structures Ver.7.0.0.; Computers and Structures Inc., Berkeley, CA, USA.
• Ramadan, T., and Ghobarah, A. (1995), “Analytical model for shear-link behavior”, J.Struct.Eng., 121(11), 1574-1580. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:11(1574)
• Fajfar, P. (2000), “A nonlinear analysis method for performance-based seismic design”, Earthq. Spectra, 16(3), 573-592. https://doi.org/10.1193/1.1586128
• Vamvatsikos, D., Cornell, C.A. (2002) “Incremental dynamic analysis”, Eartq. Eng. Struct. D., 31(3),491-514. https://doi.org/10.1002/eqe.141
• Aydinoğlu, M. N. (2003). An incremental response spectrum analysis procedure based on inelastic spectral displacements for multi-mode seismic performance evaluation. Bulletin of Earthquake Engineering, 1(1), 3-36. https://doi.org/10.1023/A:1024853326383