INVESTIGATION OF HOLE SHAPE EFFECT ON STATIC ANALYSIS OF PERFORATED PLATES WITH STAGGERED HOLES

Year 2021, Volume: 3 Issue: 2, 133 - 144, 01.05.2021

Mustafa Halûk Saraçoğlu , Fethullah Uslu , Uğur Albayrak

https://doi.org/10.47933/ijeir.883510

Cited By: 2

Abstract

In this paper, a series of analysis with finite element method was carried out with varying hole shapes of perforation as well as plate dimensions. Eight different models about holes that number of edges at the hole is four to infinite namely circular holes was presented. Than the analyze results of these models with different boundary conditions as fixed supported and simply supported at four edges were compared. In this study it has shown that when the number of edges for a hole is infinite, in other words when the perforation of the plate is circular, mid-point deflection is decreasing according to the other perforation styles. And also analyze results of eight different models of perforated plates are given in tables and comparative graphs.

Keywords

Ansys, Noncircular hole, 60 staggered perforated plate, square thin plate

INVESTIGATION OF HOLE SHAPE EFFECT ON STATIC ANALYSIS OF PERFORATED PLATES WITH STAGGERED HOLES

Abstract

Bu çalışmada, sonlu elemanlar yöntemi ile çeşitli delik şekilleri ve plak boyutları ile bir dizi analiz gerçekleştirilmiştir. Delikteki kenar sayısı dörtten sonsuza, yani dairesel delikler ile ilgili sekiz farklı model sunulmuştur. Daha sonra dört kenarı basit mesnetli ve ankastre mesnetli olarak farklı sınır koşullarına sahip bu modellerin analiz sonuçları karşılaştırılmıştır. Bu çalışmada, bir deliğin kenar sayısı sonsuz olduğunda, yani plağın delinmesi dairesel olduğunda orta nokta çökmesinin diğer delik şekillerine göre azaldığı gösterilmiştir. Ayrıca sekiz farklı delikli plak modelinin analiz sonuçları tablolarla ve karşılaştırmalı grafiklerle verilmiştir.

Keywords

Ansys, Dairesel olmayan delik, Kare ince plak

References

• [1] M. H. Saraçoğlu and U. Albayrak, “Linear static analysis of perforated plates with round and staggered holes under their self-weights,” Res. Eng. Struct. Mater., vol. 2, no. 1, pp. 39–47, 2016.
• [2] U. Albayrak and M. H. Saraçoğlu, “Analysis of Regular Perforated Metal Ceiling Tiles,” Int. J. Eng. Technol., vol. 10, no. 6, pp. 440–446, 2018.
• [3] S. Singh, K. Kulkarni, R. Pandey, and H. Singh, “Buckling analysis of thin rectangular plates with cutouts subjected to partial edge compression using FEM,” J. Eng. Des. Technol., vol. 10, no. 1, pp. 128–142, Mar. 2012. [4] U. B. Andh, S. M. Chavan, S. G. Kulkarni, and S. N. Khurd, “Stress analysis of perforated plates under uniaxial compression using FEA and photoelasticity,” Int. Res. J. Eng. Technol., 2016.
• [5] J. Rezaeepazhand and M. Jafari, “Stress analysis of perforated composite plates,” Compos. Struct., vol. 71, no. 3–4, pp. 463–468, Dec. 2005.
• [6] A. M. Sayed, “Numerical analysis of the perforated steel sheets under uni-axial tensile force,” Metals (Basel)., vol. 9, no. 6, pp. 1–16, 2019.
• [7] M. Diany, “Effects of the Position and the Inclination of the Hole in Thin Plate on the Stress Concentration Factor,” vol. 2, no. 12, pp. 8–12, 2013.
• [8] R. H. R. Bailey, “Behaviour of perforated plates under plane stress,” J. Mech. Eng. Sci., vol. 2, no. 2, pp. 143–165, 1960.
• [9] M. Jafari and M. Jafari, “Effect of hole geometry on the thermal stress analysis of perforated composite plate under uniform heat flux,” J. Compos. Mater., vol. 53, no. 8, pp. 1079–1095, 2019.
• [10] E. Pascu, A., Oleksik, M., Avrigean, “Experimental method for determining forces at bending of perforated plates,” Acta Uıversıtatıs Cıbınıensıs – Tech. Ser., vol. 69, no. 1, pp. 52–58, 2017.
• [11] H. Achtelik, G. Gasiak, and J. Grzelak, “Strength tests of axially symmetric perforated plates for chemical reactors: Part 2-Experiments,” Int. J. Press. Vessel. Pip., vol. 85, no. 4, pp. 257–264, 2008.
• [12] M. M. Konieczny, H. Achtelik, and G. Gasiak, “Finite element analysis (FEA) and experimental stress analysis in circular perforated plates loaded with concentrated force,” Frat. ed Integrita Strutt., vol. 14, no. 51, pp. 164–173, 2020.
• [13] K. Kalita and S. Halder, “Static analysis of transversely loaded isotropic and orthotropic plates with central cutout,” J. Inst. Eng. India Ser. C, vol. 95, no. 4, 2014.
• [14] C. Atanasiu and S. Sorohan, “Displacements and stresses in bending of circular perforated plate,” IOP Conf. Ser. Mater. Sci. Eng., vol. 147, no. 1, 2016.
• [15] G. Lorenzini et al., “Numerical evaluation of the effect of type and shape of perforations on the buckling of thin steel plates by means of the constructal design method,” Int. J. Heat Technol., vol. 34, no. S1, pp. S9–S20, Jan. 2016.
• [16] D. Helbig, C. C. C. Da Silva, M. de V. Real, E. D. dos Santos, L. A. Isoldi, and L. A. O. Rocha, “Study about buckling phenomenon in perforated thin steel plates employing computational modeling and constructal design method,” Lat. Am. J. Solids Struct., vol. 13, no. 10, pp. 1912–1936, 2016.
• [17] Timoshenko, S, Goodier, J. N., Theory of Elasticity. McGraw-Hill, Newyork, USA, 1951.
• [18] A. Swanson Analysis System Inc., “ANSYS User’s manual.” 2005.